785535 Volvo.Penta Gear


785535 Gear Volvo.Penta D42A; D42A PP Gear

Buy Gear 785535 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$20.00
 

14-10-2023
1.7[0.77] Pounds
-: -
New Engine Maintenance Kit Compatible with/Replacement for Briggs & Stratton 625e, 657ex, 725ex and 625-675 Series, Compatible with/Replacement for 3.5 Thru 6.75 Gross HP Quantum Engines 5139, 5140
Specs: Packaging type: Branded box. || Compatible with/Replacement for OEM Number: Briggs & Stratton 5139, 5140, 5140B || Fits: Briggs & Stratton: 625e, 657ex, 725ex and 625-675 Series; for 3.5 thru 6.75 Gross HP Quantum engines || Stens one-year warranty ensures reliability and performance for every part || Stens branded parts are trusted by professional dealers to perform OEM quality repairs.  The Stens name is featured on all Genuine Stens product packaging.
£48.85
 

13-07-2017

FAAC: FAAC
FAAC DEC SLHP 785535
Wire-in Decoder Board.||Category: Frequency Card||Obstacle Detection: Built-In Obstacle Detection
$258.29
 

24-01-2018
195 Hundredths Pounds
A1 Cardone: A1 Cardone
Cardone 78-5535 Remanufactured Ford Computer
On-car vehicle validation testing ensures product fits and functions properly||OE components with high failure rates are 100% replaced||All electronic modules are 100% tested to ensure they meet OE requirements for the application||Advanced robotic equipment ensures precision made units and consistent high quality with every part||Every unit is 100% tested to ensure quality and reliability
Number on catalog scheme: 25
 

Compatible models:

D42A; D42A PP   Volvo.Penta

Volvo Penta entire parts catalog list:

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Operate the engine until normal operating temperature is achieved. Stop the engine. Remove the crankcase oil drain plugs. The oil drain plug from the deep portion of the oil pan should be removed. Drain the oil from the crankcase for 20 minutes.
Remove the used oil filter(s). Install the new oil filter(s). Install the oil drain plugs and tighten to 70 15 N m (50 11 lb ft). Note: Your engine may be equipped with auxiliary oil filters. The auxiliary oil filters require a different volume of oil. Refer to the OEM specifications for the auxiliary oil filter.
Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for information about choosing the correct oil for your engine.
Table 1
Quantity of Oil
A 30 L (31.7 qt)
B 1 L (1.1 qt)
C 3 L (3.2 qt)
D
Total Capacity of the Lubrication System for Engine Oil
Pour quantity "A" of engine oil into the crankcase.
Allow enough time for the oil to drain into the crankcase. Approximately 20 minutes should be allowed. Check the oil level. Wait for several minutes and check the oil level again. Proceed after the oil level stops changing.
Check the oil level on the oil level gauge. The oil level should be at the "ADD" mark. If the oil level is not at the existing "ADD" mark, grind off the "ADD" mark and engrave the new "ADD" level. Use an engraving pen in order to engrave the new "ADD" mark.
Pour quantity "B" of oil into the crankcase. Allow enough time for the oil to drain into the crankcase.
Check the oil level on the oil level gauge. The oil level should be at the "FULL" mark. If the oil level is not at the existing "FULL" mark, grind off the "FULL" mark. Use an engraving pen in order to engrave the new "FULL" mark.
Pour quantity "C" of oil into the crankcase in order to allow oil to fill the oil filter.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Start the engine. Ensure that the lubrication system is filled. Inspect the engine for oil leaks.
Stop the engine and allow enough time for the oil to drain into the crankcase.
Check the oil level on the oil level gauge. If the oil level is not at the calibrated "FULL" mark, fill the crankcase to the calibrated "FULL" mark. Record the amount of oil that was added as quantity D. Record the oil capacity of the lubrication system for future oil changes.


Parts gear Volvo Penta:

815352
 
815352 Gear ring
D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83, TD61A; TD61AW; TD61ACE, TD70G; TD70G-83; TD70GPP
787854
 
787854 Gear
D42A; D42A PP
787299
 
787299 Gear
D42A; D42A PP, TD30A; TD31ACE; TD40A
785789
 
785789 Gear
D42A; D42A PP, TD30A; TD31ACE; TD40A
785435
 
785435 Gear, GEAR
D42A; D42A PP
785520
Gear ring
785520 Gear ring
D42A; D42A PP
785459
 
785459 Gear
D42A; D42A PP
354079
Gear
354079 Gear
D42A; D42A PP
Back to top