30667900 Volvo.Penta Governor


30667900 Governor Volvo.Penta D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H Governor
30667900 Governor Volvo Penta
Rating:
68

Buy Governor 30667900 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$213.22
 

10-06-2019
800 Hundredths Pounds
Volvo: Volvo
Volvo 30667900, Voltage Regulator
Genuine Volvo OEM product
Number on catalog scheme: 12
 

Volvo Penta entire parts catalog list:

D3-110I-D; D3-110I-E; D3-110I-F; D3-140I-E; D3-140I-F; D3-140A-D; D3-140A-E; D3-140A-F; D3-150I-D; D3-150I-E; D3-150I-F; D3-170I-D; D3-170I-
D3-110I-G; D3-140A-G; D3-140I-G; D3-150I-G; D3-170A-G; D3-170I-G; D3-200A-G; D3-200I-G; D3-220A-G; D3-220I-G
D3-110I-H; D3-140A-H; D3-140I-H; D3-150I-H; D3-170A-H; D3-170I-H; D3-200A-H; D3-200I-H; D3-220A-H; D3-220I-H

Information:


Table 1
Typical Configuration Parameters
Parameter Programmability
Air shutoff (ON/OFF) Yes
Crank duration Yes
Crank terminate speed Yes
ECM serial number No
Engine rated speed Software dependent
Engine serial number Yes
Equipment ID Yes
Fuel correction factor Yes
Low idle speed Yes
Maximum number of crank cycles Yes
Personality Module Part Number Software dependent
Personality module release date Software dependent
Rated fuel position Yes
Total fuel Yes
Total hours Yes
Total tattletale No The Emergency Diesel Generator set (EDG) is delivered for installation with a crank duration of 10 seconds.Ensure that the "Air Shutoff" parameter is "Enabled/ON".No password is required for programming a new Electronic Control Module (ECM) during the first 100 hours of service life. This 100 hour “free configuration” feature enables the customer to tailor the programmable setpoints to the requirements of the installation. Exceptions are "Fuel Limit" and "Personality Module Mismatch".Air Shutoff
The air shutoff uses a plate that rotates on a shaft in order to shut off inlet air to the aftercooler. The engine stops because of the restricted air supply to the combustion chamber. The air shutoff only actuates for the following conditions:
The Emergency Stop button is pressed.
An overspeed shutdown occurs.
The operator manually activates the air shutoff with the emergency air shutoffs on the engine. It is not necessary to activate both of the air shutoffs in order to shut down the engine. If one air shutoff is activated, the other air shutoff is activated automatically.Both of the air shutoffs must be reset before the engine can be restarted.
Illustration 1 g00927570
(1) Reset knob for the air shutoff To reset the air shutoff, turn the reset knob to the "OPEN" position.Ensure that both of the air shutoffs are reset.Fuel Correction Factor
When the engine is shipped from the factory, an estimate of the engine's fuel consumption is programmed into the ECM. The estimate is based upon the engine's performance specifications. The actual fuel consumption can be determined with a meter that measures the flow of the fuel. Customers are likely to find a slight difference between the estimate of fuel consumption that was programmed and the actual fuel consumption. The customer can use a Cat ET service tool to program the ECM for the actual fuel consumption. A factory level security password is required in order to change this parameter.To program the ECM for the actual fuel consumption, change the Fuel Correction Factor that is already programmed into the ECM. The Fuel Correction Factor can be programmed in increments of 0.5 percent between 25 percent.Display of Engine Performance
Histogramming
The Cat ET service tool can display the trends of the engine performance. The information can be used to improve the overall performance of the engine. The historical information is stored in a format that can be used to construct histograms. Data is available for the following parameters:
Engine rpm
Percent of engine loadIncrementing the Hours of the ECM
A new ECM that is installed on an engine can be programmed to display the correct total number of operating hours for that engine. A Cat ET service tool and a factory level security password are required.Adjusting the Total Fuel Consumption for the ECM
A new ECM that is installed on an engine can be programmed to display the correct total fuel consumption for that engine. A Cat ET service tool and a factory level security password are required.Data Link Features
CAT Data Link
The CAT Data Link provides the ability for the diesel generator control panel (DGCP) to monitor various engine parameters. The communication is established through the engine vision interface module (EVIM).CAT Data Link Flash
Flash - This is a method of downloading or programming electronic information.The CAT Data Link Flash provides the capability to flash the software for the engine control with the CAT Data Link.


Parts governor Volvo Penta:

30637251
Governor
30637251 Governor
D3-110I-A; D3-110I-B; D3-110I-C, D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
Back to top