853561 Volvo.Penta Gusset fork kit

Illustration 1 g06028600
First Phase
When the engine starts and the engine is cold, the thermostat (T2) sent the water directly to the aftercoolers. The thermostat (T1) is closed.
(A.) High temperature
(B.) Low temperature
(F.) Fuel
(S.) Sea water
(T1) Thermostat (Start of opening: 70° C, on cylinder head, front)
(T2) Thermostat (Start of opening: 50° C, on water/sea water heat exchanger)
(1) Aftercooler (high pressure)
(2) Sea water pump
(3) Fuel cooler
(4) Water/sea water heat exchanger
(5) Oil/coolant heat exchanger
(6) Coolant expansion tank
(7) Water pump
(8) Aftercooler (low pressure)
(9) Exhaust manifold
Illustration 2 g06049754
Second Phase
When the engine temperature increases, the thermostat (T2) sent the water to the Low Temperature side of the water/sea water heat exchanger.
(A.) High temperature
(B.) Low temperature
(F.) Fuel
(S.) Sea water
(T1) Thermostat (Start of opening: 70° C, on cylinder head, front)
(T2) Thermostat (Start of opening: 50° C, on water/sea water heat exchanger)
(1) Aftercooler (high pressure)
(2) Sea water pump
(3) Fuel cooler
(4) Water/sea water heat exchanger
(5) Oil/coolant heat exchanger
(6) Coolant expansion tank
(7) Water pump
(8) Aftercooler (low pressure)
(9) Exhaust manifold
Illustration 3 g06049774
Third Phase
When the engine temperature increases, the thermostat (T2) sent the water to the Low Temperature side of the water/sea water heat exchanger, the thermostat (T1) sent the water to the High Temperature side of the water/seawater heat exchanger.
(A.) High temperature
(B.) Low temperature
(F.) Fuel
(S.) Sea water
(T1) Thermostat (Start of opening: 70° C, on cylinder head, front)
(T2) Thermostat (Start of opening: 50° C, on water/sea water heat exchanger)
(1) Aftercooler (high pressure)
(2) Sea water pump
(3) Fuel cooler
(4) Water/sea water heat exchanger
(5) Oil/coolant heat exchanger
(6) Coolant expansion tank
(7) Water pump
(8) Aftercooler (low pressure)
(9) Exhaust manifoldCoolant Flow Circuit
Illustration 4 g06020332
(10) Aftercooler (high pressure)
(11) Oil/coolant heat exchanger
(12) Aftercooler (low pressure)
(13) Coolant tank
(14) Thermostat (70 °C)
Illustration 5 g06020367
(15) Riser exhaust gas pipe - sea water
(16) Coolant expansion tank
(17) Air/water heat exchanger
(18) Thermostats (50 °C)
(19) Water/sea water heat exchanger
(20) Fuel cooler
(21) Thermostats (50 °C)The centrifugal pump, rotated by the drive shaft with a poly-V belt, draws in the coolant coming from the fresh water/sea water heat exchanger or from the exhaust manifold cooling loop and sends it into the block, where it comes in contact with the engine oil heat exchanger.After the oil heat exchanger, some fresh water is sent to thermostat to the CACs to heat up the air during cold start or low temperature run and avoid condensation.The remain water touches the heat exchange areas of the cylinders and then the engine head, from which water exits flowing through the junction T fitting that contains the temperature sensors for the instrument panel and the ECU.This junction has the purpose of bypassing the coolant from the engine head to the exhaust manifold and from the manifold to the main thermostat. Which routes coolant according to the temperature either to the water/water heat exchanger or to the recirculation pump.From the bypass fitting, the liquid is then injected into the heat exchange chamber of the exhaust manifold in which the liquid flows.When liquid returns into the bypass junction, the liquid comes in contact with the wax actuator of the thermostatic valve.This will throttle flows according to temperature.Part of the liquid will enter the heat exchanger and flow through heat exchanger, releasing heat to sea water. Whereas the rest will go directly to the pump, to be recirculated.Cooling Sea Water Open Loop
Illustration 6 g06028736
(A) Sea water inlet
(B) Sea water outlet
(22) Riser exhaust gas pipe - sea water
(23) Water/sea water heat exchanger
(24) Fuel cooler
(25) Sea water pumpSea water is drawn from under the keel and filtered. Then the pump sends sea water to the fuel cooler then to the water/water heat exchanger of the closed cooling loop, then liquid flow through the gearbox oil, if one is provided.Heat Exchanger
The plate heat exchanger consists of a pack of corrugated metal plates with portholes for the passage. When the fluid passes between the plates and that is when the heat transfer will take place.The plate pack is assembled between a fix frame plate and a movable pressure plate and compressed by tightening bolts.The plates are fitted with a gasket which seals the interplate channel and directs the fluids into alternate channels. The number of plates is determined by the flow rate, physical properties of the fluids, pressure drop, and temperature program. The plate corrugations promote fluid turbulence and support the plates against differential pressure.The plate and the pressure plate are suspended from an upper carrying bar and located by a lower guiding bar.Connections are located in the frame plate. If either or both fluids make more than a single pass within the unit, in the frame and pressure plates.