866799 Volvo.Penta Heat shield


866799 Heat shield Volvo.Penta TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1230G; TD1210G; TWD1210G, TAMD103A, TD610G; TWD610G; TD710G Heat
866799 Heat shield Volvo Penta
Rating:
23

Buy Heat shield 866799 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Volvo Penta entire parts catalog list:

TAD1030G; TD1010G; TWD1010G
TAD1030GE; TAD1031GE; TAD1032GE; TAD1031G
TAD1230G; TD1210G; TWD1210G; TWD1211G; TAD1231GE; TAD1232GE
TAMD103A
TD610G; TWD610G; TD710G; TWD710G; TAD730G; TWD740GE; TAD740GE; TAD741GE

Information:

Start By:a. remove crankshaft pulley and vibration damper
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Remove four bolts (1) from adapter (2), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (4) and crankshaft seal (3) from adapter (2).
Typical Example3. Install tool (B) in the adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (5). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal & Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak.
1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3).3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean 1P0808 All Purpose Lubricant on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft pulley and vibration damper


Parts heat Volvo Penta:

3825963
 
3825963 Heat exchanger eleme
TAMD103A, TMD100C, TMD102A; TAMD102A; TAMD102D
1622523
 
1622523 Heat shield
TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD1
3832766
 
3832766 Heat shield
TAD1030GE; TAD1031GE; TAD1032GE
3832802
 
3832802 Heat shield
TAD1030GE; TAD1031GE; TAD1032GE
3836606
 
3836606 Heat shield
TAD1030GE; TAD1031GE; TAD1032GE
847152
Heat shield
847152 Heat shield
TAD1230G; TD1210G; TWD1210G, TD120HP-86; TD121; TD121G, TID120FPP; TID120FG; TD120G, TID121FG
3827217
 
3827217 Heat shield
TD610G; TWD610G; TD710G
3830182
 
3830182 Heat shield
TD610G; TWD610G; TD710G
Back to top