940160 Volvo.Penta Hexagon screw


940160 Hexagon screw Volvo.Penta 430; 430A; 430B, 500; 500A; 501A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ190A; AQ240A, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, AQD70D; TAMD70D; TAMD70E, BB231A; BB261A, Hexagon
940160 Hexagon screw Volvo Penta
Rating:
63

Buy Hexagon screw 940160 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$37.81
 

29-11-2023

-: -
Teng Tools 1-7/8 Inch 6 Point 3/4 Inch Drive SAE Shallow Chrome Molybdenum Impact Socket,Mechanic Tool,Hand Tool - 940160
[ EXTRA STRONG ] The impact socket is made from heavy duty chrome molybdenum (CR-MO) steel for exceptional strength and flexibility. || [ LASTS FOR YEARS ] Black phosphate finish for maximum protection and durability. || [ GREAT GRIP ] 6 point high torque design grips flat sides of a fastener, not corners, preventing round-off. || [ INSTANT IDENTIFICATION ] The impact socket features roll stamped markings to ensure permanent and instant socket identification. || [ SAFE TO USE ] Designed for use with a locking pin and ring to increase safety when working with pneumatic tools. Size: 1-7/8 inch. Length: 2.68 inches
$8.90

29-01-2025

US: Toolsmithdirect
Powerbuilt 940160 1/2" Dr. 12 Pt. Metric Deep Well Socket, 19mm
Powerbuilt Made to be the most reliable tools in the market today || Tool solutions for most all situations || Built to exceed tool standards
$19.53
 

23-10-2018

Powerbuilt: Powerbuilt
Powerbuilt? 1/2 Drive 19mm 12 Pt. Metric Deep Socket - 940160
Drive 12 Point Metric Deep Socket||Weight: 0.3753 lbs||Standard and deep well socket lengths exceed ANSI standards and have the center hole punched through||Powerbuilt chrome sockets feature HV high visibility size markings that are three times larger for e
Number on catalog scheme: 2
 

Compatible models:

430; 430A; 430B   500; 500A; 501A   740A; BB740A   AD31D; AD31D-A; AD31XD   AD31L-A; AD31P-A; AD41L-A   AD41D; D41D; TAMD41D   AQ115A; AQ115B; AQ130   AQ190A; AQ240A   AQ225D; AQ225E; AQ225F   AQ260A; AQ260B; BB260A   AQD70D; TAMD70D; TAMD70E   BB231A; BB261A   D100A; D100AK; D100B   D100BHC; D100BRC; TD100AHC   D120A; D120AK; TD120A   D2-55; D2-55B; D2-55C   D2-75; D2-75B; D2-75C   D70B; D70B PP; D70B K   D70CHC; D70CRC; TD70CHC   DP-C1; DP-D1; DP-S   DP-E; SP-E; TSK DP-E   DP-G; TSK DP-G   DPX-A; TSK DPX-A   KAD32P; TAMD42WJ-A; KAD43P-A   KAD42A; KAMD42A; HS1A   KAD42B; KAMD42B; TAMD42B   KAD42P-A; KAMD42P-A; HS1A   MD100A; TMD100A; TMD100AK   MD120A; MD120AK; TMD120A   MD31A; TMD31A; TMD31B   MD31A; TMD31B; TAMD31B   MD70B; MD70BK; TMD70B   MD70C; TMD70C; TAMD70C   TAD1030P   TAD1230G; TD1210G; TWD1210G   TAD1230P; TD121GP-87; TWD1210P   TAD1630P; TWD1630P; TWD1630PP   TAD1630V; TWD1630V   TAMD103A   TAMD122A; TMD122A; TAMD122P-A   TAMD162A; TAMD162B; TAMD162C   TAMD162C-C; TAMD163A-A; TAMD163P-A   TAMD165A; TAMD165C; TAMD165P   TAMD60A; TAMD60B   TAMD60C   TAMD61A; TAMD62A   TD100G-87; TD1030ME; TWD1030ME   TD100G-87; TD1030VE; TAD1030V   TD100G; TD100G-85; TD100G-87   TD120AHC; TD120ARC; TAD120AHC   TD120C   TD120HP-86; TD121; TD121G   TD120HPP; TID120HPP   TD121G-87; TWD1210V; TWD1211V   TD60A; TD60B; TD60B PP   TD60D; TD60D-83; TD60DPP-83   TD70G; TD70G-83; TD70GPP   TID120FPP; TID120FG; TD120G   TID121FG   TID162AG; TID162AGP; TID162AP   TMD100C   TMD102A; TAMD102A; TAMD102D   TMD121C; TAMD121C; TAMD121D   TMD41A; TMD41B; D41A   TMD41B; D41B; TAMD41B   TWD1230ME   TWD1620G; TWD1630G; TAD1630G   Volvo.Penta

Volvo Penta entire parts catalog list:

430; 430A; 430B; 431A; 431B; 432A; 434A; 500B; 501B; 570A; 572A; 740B; DP-A; DP-A1; DP-A2; DP-C; DP-C1; DP-C1 1.95; DP-C1 2.30; DP-D; DP-D1; DP-D1
500; 500A; 501A
740A; BB740A
AD31D; AD31D-A; AD31XD; TAMD31D; TMD31D
AD31L-A; AD31P-A; AD41L-A; AD41P-A; D41L-A; TAMD31L-A; TAMD31M-A; TAMD31P-A; TAMD31S-A; TAMD41H-A; TAMD41H-B; TAMD41P-A; TAMD41L-A; TAMD41M-A
AD41D; D41D; TAMD41D; TMD41D; HS1A
AQ115A; AQ115B; AQ130; AQ130A; AQ130B; AQ130C; AQ130D; AQ165A; AQ170A; AQ170B; AQ170C; AQD21A; BB115A; BB115B; BB115C; BB165A; BB170A; BB170B; BB1
AQ190A; AQ240A
AQ225D; AQ225E; AQ225F; BB225A; BB225AV; BB225B; BB225C; 275; 280B; 290A; 290DP; MS3B; MS3C; MS4A
AQ260A; AQ260B; BB260A; BB260AV; BB260B; BB260C
AQD70D; TAMD70D; TAMD70E
BB231A; BB261A
D100A; D100AK; D100B; TD100A; TD100AG; TD100AK
D100BHC; D100BRC; TD100AHC; TD100ARC
D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK
D2-55; D2-55B; D2-55C; D2-55D; D2-55E; D2-55F
D2-75; D2-75B; D2-75C; D2-60F; D2-75F
D70B; D70B PP; D70B K; TD70B
D70CHC; D70CRC; TD70CHC; TD70CRC
DP-C1; DP-D1; DP-S; DP-C1 1.95; DP-C1 2.30; DP-D1 1.68; DP-D1 1.78; DP-D1 1.95; DP-D1 2.30; TSK DP-S
DP-E; SP-E; TSK DP-E
DP-G; TSK DP-G
DPX-A; TSK DPX-A
KAD32P; TAMD42WJ-A; KAD43P-A; KAMD43P; KAMD43P-A; KAMD43P-B; KAD44P; KAD44P-B; KAD44P-C; KAMD44P-A; KAMD44P-C; KAD300-A; KAMD300-A; HS1A; HS1E
KAD42A; KAMD42A; HS1A; MS5B
KAD42B; KAMD42B; TAMD42B
KAD42P-A; KAMD42P-A; HS1A
MD100A; TMD100A; TMD100AK; TMD100A-CC; MD100B; MD100BK; MD100B-CC
MD120A; MD120AK; TMD120A; TMD120AK; TAMD120A; TAMD120AK; TMD120B; TAMD120B; TAMD120B-CC
MD31A; TMD31A; TMD31B; TAMD31A; TAMD31B; AD31; AQAD31A; AD31B; 290A; DP-A; DP-B; DP-A1; DP-B1; SP-A; SP-A1
MD31A; TMD31B; TAMD31B; AD31B
MD70B; MD70BK; TMD70B; THAMD70B; TAMD70B; AQD70BL; AQD70B
MD70C; TMD70C; TAMD70C; THAMD70C; AQD70BL; AQD70CL
TAD1030P
TAD1230G; TD1210G; TWD1210G; TWD1211G; TAD1231GE; TAD1232GE
TAD1230P; TD121GP-87; TWD1210P; TWD1211P; TD1210G; TWD1210G; TWD1211G; TD121GP

Information:


Illustration 1 g00668020
Make sure that the left hand threads in the end of the throttle shaft are clean. Thread Tool (A) into the throttle shaft. Tighten Tool (A) until the shoulder on Tool (A) bottoms out against the end of the throttle shaft.
Install throttle lever (1) on Tool (A) .Note: Throttle lever (1) and the tolerance ring should not be reused after being removed from the governor. A new 4P-3539 Throttle Lever and a new 4P-3537 Tolerance Ring are required. Apply a light machine oil to the bore of the throttle lever and the outside of the tolerance ring after the tolerance ring is seated on the throttle shaft. This will reduce the force that is required to press the throttle lever into position.
Install Tool (E) on Tool (A) and put Tool (F) in position.
Install thrust bearing (D), washer (C) and nut (B) on Tool (A) .Note: High idle screw (2) must be backed out all the way.Note: The governor fuel ratio control must be connected to a regulated air supply of 140 to 210 kPa (20 to 30 psi) during the adjusting procedure.
Increase the speed of the calibration bench to the "THROT LEV PRESS" rpm that is specified in the TMI.
Illustration 2 g00668244
Loosen screw (3) in the adjustable arm assembly. Use a 1U-7579 Hex Wrench to rotate the throttle shaft counterclockwise. Stop rotating the throttle shaft when the governor output is within the range for "THROT LEV PRESS" that is specified in the TMI.Note: Use a hex wrench to rotate the throttle shaft. Do not exceed a governor output of 0.0 mm (0.0 inch) when the throttle shaft is rotated. Before the throttle lever is pressed onto the throttle shaft, rotating the throttle shaft too far in the FUEL ON direction may cause the internal governor linkage to come loose from the pivot shaft linkage. If the internal governor linkage becomes disconnected, the governor will not pass the remainder of the adjusting procedure. The governor must be disassembled and the linkage must be reconnected. Refer to the Disassembly and Assembly section in this manual. Repeat this procedure beginning with Step 1, after the governor has been reassembled.
Illustration 3 g00668482
Use a hex wrench to tighten setscrew (3) on arm (E) while the throttle shaft is held in position. Tightening setscrew (3) will lock the throttle shaft in position.
Illustration 4 g00668541
Rotate the throttle shaft with two thumb screws (4). The two thumb screws will adjust the governor output to the final position. Keep both thumb screws tight against arm (E). When the setscrew is released the throttle shaft will be locked in position.
Decrease the speed of the calibration bench until the governor output becomes positive. When the governor output becomes positive, adjust the speed of the calibration bench to the "THROT LEV PRESS" rpm that is specified in the TMI. If the governor output is not within the range that is specified in the TMI, repeat Steps 6 through 9, if necessary.
Illustration 5 g00668613
Maintain the "THROT LEV PRESS" rpm on the calibration bench. Verify that high idle screw (2) is backed out and that throttle lever (1) is rotated fully in the counterclockwise direction so that the throttle lever touches the rear housing face. Hold the throttle lever in this position.Note: The throttle lever should sit squarely on the shaft and against the housing face. Make sure that the throttle lever is not in a bind.
Illustration 6 g00668569
Tighten nut (B) until block (F) bottoms out against throttle shaft (1) .
Loosen the setscrew on Tool (E) .
Rotate the throttle lever fully counterclockwise so the high idle bump on the throttle lever touches the rear housing face. Decrease the speed of the test bench until the governor output is positive. Return the speed of the test bench to the "THROT LEV PRESS" rpm that is specified in the TMI. Note the governor output.
If the governor output is within the range for the "THROT LEV PRESS" that is specified in the TMI, the throttle lever is correctly positioned. Proceed with the standard governor adjustment procedure. Refer to the Testing and Adjusting, "Governor (Type) - Adjust" section in this manual.
If the governor output is not within the range for the "THROT LEV PRESS" that is specified in the TMI, the throttle lever must be removed and a new lever must be installed with the correct orientation. Repeat this entire procedure after the throttle lever is installed.


Parts hexagon Volvo Penta:

940162
Hexagon screw
940162 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, AQ115A; AQ115B; AQ130, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B;
955269
 
955269 Hexagon screw
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D13B-A MP; D13B-B MP; D13B-C MP, D5A-T; D5A-TA; D5A-B TA, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MB2,
955780
 
955780 Hexagon nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-G, 4.3GXi-J; 4.3GXi-JF; 4.3OSi-J, 4.3GXiE-225-R, 4.3GXiE-M, 4.3GXiE-P; 4.3GXiE-Q, 430; 430A; 430B, 5.0GXi-G; 5.0GXi-GF; 5.0OSi-G, 5.0GXi-J; 5.0GXi-JF; 5.0OSi-J, 5.0GXiCE-270-R;
955700
 
955700 Hexagon screw
230A; 230B; 250A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A, AQ20
955549
 
955549 Hexagon screw
AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, MD100A; TMD100A; TMD100AK, MD40A; TMD40A; TMD40B, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1230G;
940092
Hexagon nut
940092 Hexagon nut
230A; 230B; 250A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ23
940186
Hexagon screw
940186 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, AQ115A; AQ115B; AQ130, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B;
955852
 
955852 Hexagon nut
AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, MB10A, MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD5A; MD5B; MD5C, MD6; MD6A; MD6B, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60C, TAMD61A; TAMD62A, TAMD71A; TAMD72A, TAMD71B; TAMD
Back to top