973522 Hexagon screw Volvo.Penta
TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TD121G-87; TWD1210V; TWD1211V, TWD1230ME
Hexagon
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
A-Premium HVAC Blower Motor Resistor Compatible with Ford Edge 2007-2011 & Lincoln MKX 2007-2011, MKT 2010-2011, 3.5L 3.7L
A-Premium [Vehicle Fitment]: Compatible with Ford Edge 2007-2011; Compatible with Lincoln MKT 2010-2011, MKX 2007-2011---Without Automatic Temperature Control; All Engine; 4 Pins || [Reference Number]: The A-Premium Blower Motor's reference number: RU635, 4P1584, 973-522, 7T4Z19A706A, 973-249, 973522, 973249. Before placing an order, verify that the part is compatible with your vehicle using the compatibility system. || [Superior Quality]: Designed to keep your vehicle's HVAC system in top shape; Durable Material: Material of rotor punching plate is silicon steel. Enameled wire is used copper enameled wire. || [Easy to Install]: Same Dimensions as OE part, Directly Fit; Stable characteristics and high reliability; Larger Air Volume and Lower Noise || [Buy with Confidence]: A-Premium offers a one-year unlimited-mileage guarantee on our meticulously crafted blower motor resistor. We offer a wide variety of automotive accessory categories, ensuring that you can hit the road with peace of mind.
A-Premium [Vehicle Fitment]: Compatible with Ford Edge 2007-2011; Compatible with Lincoln MKT 2010-2011, MKX 2007-2011---Without Automatic Temperature Control; All Engine; 4 Pins || [Reference Number]: The A-Premium Blower Motor's reference number: RU635, 4P1584, 973-522, 7T4Z19A706A, 973-249, 973522, 973249. Before placing an order, verify that the part is compatible with your vehicle using the compatibility system. || [Superior Quality]: Designed to keep your vehicle's HVAC system in top shape; Durable Material: Material of rotor punching plate is silicon steel. Enameled wire is used copper enameled wire. || [Easy to Install]: Same Dimensions as OE part, Directly Fit; Stable characteristics and high reliability; Larger Air Volume and Lower Noise || [Buy with Confidence]: A-Premium offers a one-year unlimited-mileage guarantee on our meticulously crafted blower motor resistor. We offer a wide variety of automotive accessory categories, ensuring that you can hit the road with peace of mind.
$266.76
31-10-2022
-: -
Harvey Tool Corner Radius & Corner Chamfer End Mills(Pack of 2)(973522)
Mill Diameter (mm):1.00 || Mill Diameter (Decimal Inch):0.0394 || End Type:Corner Radius || Corner Radius (mm):0.08 || Number of Flutes:3
Mill Diameter (mm):1.00 || Mill Diameter (Decimal Inch):0.0394 || End Type:Corner Radius || Corner Radius (mm):0.08 || Number of Flutes:3
Compatible models:
Volvo Penta entire parts catalog list:
- Exhaust Manifold, High Mounted Turbo » 973522
TD121G-87; TWD1210V; TWD1211V; TAD1230V; TWD1230VE; TWD1231VE
- Exhaust Manifold, High Mounted Turbo: A
- Exhaust Manifold, High Mounted Turbo: B
- Exhaust Manifold, Low Mounted Turbocharger
Information:
Table 1
Oil Change Interval For the C280-16 Engine
Engine Lube Oil Capacity(1) Oil Change Interval(2)
C280-12 1268 L (335 US gal) 1050 Service Hours
(1) The capacity includes the oil sump plus oil filters that are installed at the factory. Engines with auxiliary oil filters will require additional oil. The capacity is approximate. The actual capacity may vary by 5 percent. Caterpillar recommends using the capacity that is listed and then adjusting the oil level according to the oil level gauge (dipstick).
(2) Use this oil change interval in the absence of oil analysis.Change the Engine Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase with the oil warm. This method allows the waste particles that are suspended in the oil to drain.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.
Ensure that the engine is stopped before performing this procedure. Attach a DO NOT OPERATE tag to the starting controls.
Note: Drain the oil into a suitable container. Dispose of fluids according to local regulations.
Illustration 1 g00130760
(1) Drain valve
Open drain valve (1) in order to drain used oil. After the oil has drained, close drain valve (1). Note: If a suction device is used in order to remove the oil from the oil pan, ensure that the suction device is clean. This procedure will prevent dirt from entering the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
Clean the oil suction screen. Note: Approximately 1 L (1 qt) of oil will remain in the housing after the sump has been drained. This oil will pour out of the housing when the cover for the oil suction screen is removed. Prepare to catch the oil in a suitable container. Clean up any spilled oil with absorbent towels or pillows. DO NOT use absorbent particles to clean up the oil.
Illustration 2 g00540945
(2) Cover
(3) Seal
(4) Screen
Remove cover (2) and seal (3). Discard the used seal. Slide screen assembly (4) from the tube.
Wash the screen assembly in clean nonflammable solvent. Allow the screen assembly to dry before installation.
Clean the bottom of the sump. Remove side covers in order to gain access to the sump. When the bottom of the sump is clean, install the side covers.
Install the oil suction screen. Install the cover and a new seal.
Change the engine oil filters. See this Operation and Maintenance Manual, "Engine Oil Filter - Change" topic (Maintenance Section).
Clean the centrifugal oil filters.
Disassemble the centrifugal oil filters according to the instructions in the Service Manual.
Thoroughly clean all of the parts of the centrifugal oil filter. Carefully inspect all of the parts.
Ensure that all of the rotor components are thoroughly clean before assembling the rotor. Failure to do so can cause an out of balance condition that can cause rapid wear to the bearings and the spindle.
Note: Install a new paper liner when the centrifugal oil filter is assembled.
Assemble the centrifugal oil filters according to the instructions in the Service Manual.
Only use oils that are recommended by Caterpillar. For the proper oil to use, refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section).
Engine damage can occur if the crankcase is filled above the "FULL" mark on the oil level gauge (dipstick).An overfull crankcase can cause the crankshaft to dip into the oil. This will reduce the power that is developed and also force air bubbles into the oil. These bubbles (foam) can cause the following problems: reduction of the oil's ability to lubricate, reduction of oil pressure, inadequate cooling, oil blowing out of the crankcase breathers and excessive oil consumption.Excessive oil consumption will cause deposits to form on the pistons and in the combustion chamber. Deposits in the combustion chamber lead to the following problems: guttering of the valves, packing of carbon under the piston rings and wear of the cylinder liner.If the oil level is above the "FULL" mark on the oil level gauge, drain some of the oil immediately.
Remove the oil filler cap. Fill the crankcase through the oil filler tube only. Clean the oil filler cap. Install the oil filler cap.
Start the engine according to this Operation and Maintenance Manual, "Engine Starting" topic (Operation Section).
Operate the engine at low idle for 2 minutes. Inspect the engine for oil leaks.
Ensure that the oil level is at the "FULL" mark on the "LOW IDLE" side of the oil level gauge.
Stop the engine and allow the oil to drain back into the sump for a minimum of 10 minutes.
Remove the oil level gauge and check the oil level. Maintain the oil level to the "FULL" mark on the "ENGINE STOPPED" side of the oil level gauge.
Parts hexagon Volvo Penta:
940162
940162 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, AQ115A; AQ115B; AQ130, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B;
955536
955536 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AQ115A; AQ115B; AQ130, AQ175A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; B
955269
955269 Hexagon screw
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D13B-A MP; D13B-B MP; D13B-C MP, D5A-T; D5A-TA; D5A-B TA, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MB2,
955523
955523 Hexagon screw
2001; 2001B; 2001AG, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ175A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C,
955780
955780 Hexagon nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-G, 4.3GXi-J; 4.3GXi-JF; 4.3OSi-J, 4.3GXiE-225-R, 4.3GXiE-M, 4.3GXiE-P; 4.3GXiE-Q, 430; 430A; 430B, 5.0GXi-G; 5.0GXi-GF; 5.0OSi-G, 5.0GXi-J; 5.0GXi-JF; 5.0OSi-J, 5.0GXiCE-270-R;
955779
955779 Hexagon nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B,
940133
940133 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31L-A; AD31P-A; AD41L-A, AQ115A; AQ115B; AQ130, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B;
959794
959794 Hexagon screw
430; 430A; 430B, 571A, AQ190A; AQ240A, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ290A, AQ311A; AQ311B, AQD70D; TAMD70D; TAMD70E