994174 Volvo.Penta Hexagon screw


994174 Hexagon screw Volvo.Penta D16C-A MG, D9A2A; D9A2A MG; D9A2A D9A-MG Hexagon
994174 Hexagon screw Volvo Penta
Rating:
38

Buy Hexagon screw 994174 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$313.95

29-11-2024
1.0[0.45] pounds
US: Global Commercial Pa
Salvajor 994174 SALVAJOR 994174 CONTACTOR 24V (994174)
Salvajor
$71.37
 

14-03-2023

-: -
Aftermarket replacement 994174 Water Pump Kit for Clark
Please Note That Some Listings Use Stock Images As A Reference For Customers note that all OEM part numbers and logos are to be used for identification purposes only || CL994174
Number on catalog scheme: 10
 

Compatible models:

Volvo Penta entire parts catalog list:

Information:

Note: Check all of the O-ring seals and the components for wear or for damage. Replace the components, if necessary. Replace all of the gaskets prior to assembly. Lubricate all of the O-ring seals lightly with the lubricant that is being sealed. Clean all of the components with a cloth that is free of loose material (lint).
Illustration 1 g00712036
Position a new gasket (30) on the engine block. Make sure that all four joints (X) of gasket (30) are positioned correctly. Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to each joint (X) .
Illustration 2 g00712008
Illustration 3 g00652707
Apply 4C-9508 Wicking Sealant to the eight 1/2 in - 13 NC twelve point head bolts (29). Use two people in order to lift oil pan (front) (26) into position, as shown. The weight of the oil pan (front) is 39 kg (85 lb). Install 17 twelve point head bolts (29) and the hard washers that hold oil pan (front) (26) in position.
Position plate (28) on oil pan (front) (26). Install two bolts (27) and the hard washers that hold plate (28) in position.
Position a new integral seal (not shown) on the surface of oil pan (front) (26) that mates with the oil pan (middle). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of the integral seal and gasket (30) .
Illustration 4 g00652705
Illustration 5 g00652706
Lift oil pan (middle) (22) into position, as shown. Install 12 bolts (24) and the hard washers that hold oil pan (middle) (22) in position.
Install eight bolts (23) and the hard washers that hold oil pan (middle) (22) to the oil pan (front).
Position a new integral seal (21) on the surface of oil pan (middle) (22) that mates with oil pan (rear) (19). Apply 8T-9014 Silicone Sealant or 7M-7260 Liquid Gasket to the intersections of integral seal (21) and gasket (30) .
Apply 4C-9508 Wicking Sealant to the two 1/2 in - 13 NC twelve point head bolts (25). Lift oil pan (rear) (19) into position, as shown. Install 11 bolts (25) and the hard washers that hold oil pan (rear) (19) in position.
Install eight bolts (20) and the hard washers that hold oil pan (middle) (22) to oil pan (rear) (19) .
Illustration 6 g00652704
Position support (18) on the oil pan (rear). Install four bolts (17) and the hard washers that hold support (18) in position.
Illustration 7 g00711824
Illustration 8 g00711857
Install two bolts (9) (not shown) and the hard washers that hold the two plates together.
Position seal (15) and O-ring seal (16) on oil pump inlet elbow (12). Position O-ring seal (14) on pump inlet elbow (8) .
Position oil pump inlet elbow (12) and pump inlet elbow (8) on the oil pan (front), as shown. Install five bolts (10), bolt (11), and the hard washers that hold oil pump inlet elbow (12) in position. Install two bolts (7) that hold pump inlet elbow (8) in position.
Connect wire harness (13) for the liquid level switch at the electrical connection.
Illustration 9 g00711770
Connect tube assembly (5) and hose assembly (6) to the oil pan (front).Note: Hose assembly (6) is only present on machines that are equipped with the engine prelubrication system.
Illustration 10 g00652699
Illustration 11 g00711796
Position tube assembly (dipstick) (2) to the oil pan. Install two nuts (1) and the hard washers that hold the lower end of tube assembly (2) in position. Tighten the nuts to a torque of 35 5 N m (26 4 lb ft).
Tighten bolt (3) and two clamps (4) that hold tube assembly (2) to the bracket. Repeat for the remaining two clamps.
Tighten the oil drain plug (not shown) to a torque of 110 15 N m (81 11 lb ft). Tighten the bolt (not shown) on the bottom of the oil pan (rear) to a torque of 55 7 N m (41 5 lb ft).
Fill the engine w


Parts hexagon Volvo Penta:

940135
Hexagon screw
940135 Hexagon screw
430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AQ115A; AQ115B; AQ130, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, A
940197
 
940197 Hexagon nut
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, AQ290A, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; T
955366
 
955366 Hexagon screw
AD30A; AQAD30A; MD30A, D100A; D100AK; D100B, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D5A-T; D5A-TA; D5A-B TA, D5A-T
955785
 
955785 Hexagon nut
AD30A; AQAD30A; MD30A, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D1
963537
 
963537 Hexagon screw
D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, MD31A; TMD31A; TMD31B, TMD41A; TMD41B; D41A
3830665
 
3830665 Hexagon screw
D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH
983717
 
983717 Hexagon nut
1372, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE;
984877
 
984877 Hexagon screw
D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG
Back to top