62260 Hollow screw Volvo.Penta
D100A; D100AK; D100B, D70B; D70B PP; D70B K
Hollow
Price: query
Rating:
Compatible models:
D100A; D100AK; D100B
D70B; D70B PP; D70B K
Volvo.Penta
Volvo Penta entire parts catalog list:
D70B; D70B PP; D70B K; TD70B
Information:
Illustration 1 g01057701
Illustration 2 g01151217
Terminal locations at the ECM connector (P1-48) Unswitched +Battery (P1-52) Unswitched +Battery (P1-53) Unswitched +Battery (P1-55) Unswitched +Battery (P1-63) −Battery (P1-65) −Battery (P1-67) −Battery (P1-69) −Battery (P1-70) KeyswitchTest Step 1. Inspect the Electrical Connectors and the Wiring
Thoroughly inspect the J1/P1 ECM connector, the battery connections and the connections to the keyswitch. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the following connections:
P1-48
P1-52
P1-53
P1-55
P1-63
P1-65
P1-67
P1-69
P1-70
Check the allen head screw at each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for correct torque values.
Check the harness and wiring for abrasion and for pinch points from the battery to the ECM, and from the keyswitch to the ECM.Expected Result:Ensure that all connectors, pins and sockets are completely coupled and/or inserted. Ensure that the harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK, Troubleshooting a 43-02 Code - Proceed to Test Step 2.
OK, Troubleshooting a 168-02 Code - Proceed to Test Step 3.
Not OK - A problem has been identified with the connectors or with the wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Use Cat ET to Check the Status of the Keyswitch
Turn the keyswitch to the OFF position.
Connect Cat ET to the data link connector and access the status screen that shows the status of the keyswitch.
Monitor the status of the keyswitch while the keyswitch is being cycled slowly from the ON position to the OFF position.Note: Cat ET may indicate that a new ECM has been detected. This condition is normal, due to a powerdown of the ECM with the keyswitch in the OFF position.Note: Cycling the keyswitch several times may cause additional 43-02 faults to be logged. This is normal. Clear any logged faults.Expected Result:The status of the keyswitch changes from "ON" with the keyswitch in the ON position to "OFF" with the keyswitch in the OFF position.Results:
OK - The input for the keyswitch is functioning properly at this time.Repair: The problem appears to be resolved. If an intermittent electrical condition is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect" for details that are related to troubleshooting intermittent electrical conditions. Excessive cycling of the keyswitch can cause this fault to be logged. This is normal. Clear any logged faults.STOP
Not OK - The status of the keyswitch did not change. Proceed to Test Step 3.Test Step 3. Check the Battery Voltage at the ECMPerform Steps A, B, C, D and E if the 168-02 ECM Battery Power Intermittent (51) is active or logged:
Illustration 3 g01151221
Pin locations on breakout T (48) Unswitched +Battery (52) Unswitched +Battery (53) Unswitched +Battery (55) Unswitched +Battery (63) −Battery (65) −Battery (67) −Battery (69) −Battery (70) Keyswitch
Disconnect the P1 ECM connector and insert a breakout T.Refer to Illustration 3 for the breakout T.
Measure the voltage between terminal 48 unswitched +Battery and terminal 63 -Battery.
Measure the voltage from terminal 52unswitched +Battery and terminal 65 -Battery.
Measure the voltage between terminal 53 unswitched +Battery and terminal 67 -Battery.
Measure the voltage between terminal 55 unswitched +Battery and terminal 69 -Battery.Refer to Illustration 3 for the breakout T.Perform Steps F, G, H, and I if 43-02 Key Switch Fault (71) is active or logged:
Disconnect P1 ECM connector and insert a breakout T.
Turn the keyswitch to the ON position.
Measure the voltage between P1-70 keyswitch and the following terminals:
P1-63
P1-65
P1-67
P1-69Expected Result:For 12 volt systems, the measured voltage is a constant 11.0 to 13.5 VDC with no suspected intermittent problems at this time.For 24 volt systems, the measured voltage is a constant 22.0 to 27.0 VDC with no suspected intermittent problems at this time.Results:
OK - The ECM is receiving the correct voltage. Repair: The battery circuit and/or the keyswitch circuits appear to be functioning correctly at this time. If an intermittent electrical condition is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect" for details that are related to troubleshooting intermittent electrical conditions.STOP
Not OK - Battery Voltage Out of Range - Th
Parts hollow Volvo Penta:
74033
74033 Hollow screw
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D12D-A MG; D12D-E MG, D12D-A MH; D
25167
25167 Hollow screw
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ120B; AQ125A; AQ140A, AQ145A; BB145A, AQ175A, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B;
48634
48634 Hollow screw
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D120A; D120AK; TD120A, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D70B; D70B PP; D70B K, D70CHC; D70C
942081
942081 Hollow screw
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAMD122A; TMD122A; TAMD122P-A, TD1
6210714
6210714 Hollow screw
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD30A; TD31ACE; TD40A, TD70G; TD70G-83; TD70GPP
823417
823417 Hollow screw
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D5A-T; D5A-TA; D5A-B TA, D70CHC; D70CRC; TD70CHC, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C;
836832
836832 Hollow screw
D100A; D100AK; D100B, D120A; D120AK; TD120A, TD120C, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP, TID120FPP; TID120FG; TD120G
424205
424205 Hollow screw
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, TD120AHC; TD120ARC; TAD120AHC