3887212 Volvo.Penta Hose

Table 1
Cross-Reference from CID-FMI Code on Cat Data Link to Troubleshooting Procedure    
Code and Description    Procedure    
1-5 Cylinder #1 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
1-6 Cylinder #1 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
2-5 Cylinder #2 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
2-6 Cylinder #2 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
3-5 Cylinder #3 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
3-6 Cylinder #3 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
4-5 Cylinder #4 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
4-6 Cylinder #4 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
5-5 Cylinder #5 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
5-6 Cylinder #5 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
6-5 Cylinder #6 Injector current below normal     Troubleshooting, "Injector Solenoid - Test"    
6-6 Cylinder #6 Injector current above normal     Troubleshooting, "Injector Solenoid - Test"    
41-3 8 Volt DC Supply voltage above normal     Troubleshooting, "Sensor Supply - Test"    
41-4 8 Volt DC Supply voltage below normal     Troubleshooting, "Sensor Supply - Test"    
42-5 Injection Actuation Valve current below normal     Troubleshooting, "Injection Actuation Pressure Control Valve - Test"    
42-6 Injection Actuation Valve current above normal     Troubleshooting, "Injection Actuation Pressure Control Valve - Test"    
91-8 Throttle Position Sensor abnormal frequency, pulse width, or period     Troubleshooting, "Speed Control - Test"    
94-3 Fuel Delivery Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
94-4 Fuel Delivery Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
100-3 Engine Oil Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
100-4 Engine Oil Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
110-3 Engine Coolant Temperature Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Passive) - Test"    
110-4 Engine Coolant Temperature Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Passive) - Test"    
164-3 Injector Actuation Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
164-4 Injector Actuation Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
168-0 Electrical System Voltage high - most severe (3)     Troubleshooting, "Electrical Power Supply - Test"    
168-1 Electrical System Voltage low - most severe (3)     Troubleshooting, "Electrical Power Supply - Test"    
168-2 Electrical System Voltage erratic, intermittent, or incorrect     Troubleshooting, "Electrical Power Supply - Test"    
172-3 Intake Manifold Air Temperature Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Passive) - Test"    
172-4 Intake Manifold Air Temperature Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Passive) - Test"    
190-8 Engine Speed Sensor abnormal frequency, pulse width, or period     Troubleshooting, "Speed/Timing - Test"    
253-2 Personality Module erratic, intermittent, or incorrect     Troubleshooting, "ECM Software - Install"    
261-11 Engine Timing Offset fault     Troubleshooting, "Timing - Calibrate"    
261-13 Engine Timing Calibration calibration required     Troubleshooting, "Timing - Calibrate"    
262-3 5 Volt Sensor DC Power Supply voltage above normal     Troubleshooting, "Sensor Supply - Test"    
262-4 5 Volt Sensor DC Power Supply voltage below normal     Troubleshooting, "Sensor Supply - Test"    
267-2 Remote Shutdown Input erratic, intermittent, or incorrect     Troubleshooting, "Shutdown (Ground Level) - Test"    
268-2 Programmed Parameter Fault erratic, intermittent, or incorrect     Troubleshooting, "Configuration Parameters"    
269-3 Sensor Power Supply voltage above normal     Troubleshooting, "Sensor Supply - Test"    
269-4 Sensor Power Supply voltage below normal     Troubleshooting, "Sensor Supply - Test"    
274-3 Atmospheric Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
274-4 Atmospheric Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
275-3 Right Turbocharger Inlet Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
275-4 Right Turbocharger Inlet Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
296-9 Transmission Control abnormal update rate     Troubleshooting, "Cat Data Link - Test"    
296-14 Transmission Control special instruction     (1)    
298-2 Service Brake Pedal Switch erratic, intermittent, or incorrect     Troubleshooting, "Throttle Lock - Test"    
342-8 Secondary Engine Speed Sensor abnormal frequency, pulse width, or period     Troubleshooting, "Speed/Timing - Test"    
617-5 Inlet Air Heater Relay current below normal     Troubleshooting, "Air Inlet Heater - Test"    
617-6 Inlet Air Heater Relay current above normal     Troubleshooting, "Air Inlet Heater - Test"    
1785-3 Intake Manifold Pressure Sensor voltage above normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
1785-4 Intake Manifold Pressure Sensor voltage below normal     Troubleshooting, "Sensor Signal (Analog, Active) - Test"    
1785-10 Intake Manifold Pressure Sensor abnormal rate of change     Troubleshooting, "Sensor Supply - Test"    
( 1 ) The engine ECM has not received an expected parameter from the transmission ECM. Ensure that each ECM has the latest flash file. Reinstall the ECM software, if necessary. Ensure that the programmable parameters for each ECM are correctly configured. Check for an intermittent problem in a connector or in the harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for related information.D