8149606 Volvo.Penta Hose


8149606 Hose Volvo.Penta TD610V; TWD610V; TD630VE, TD71A; TID71A; TWD710V, TWD1240VE; TAD1241VE; TAD1242VE Hose
8149606 Hose Volvo Penta
Rating:
38

Buy Hose 8149606 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Volvo Penta entire parts catalog list:

TD610V; TWD610V; TD630VE; TWD630VE; TD640VE; TWD610PB
TD71A; TID71A; TWD710V; TD730VE; TWD731VE; TAD730V; TWD740VE
TWD1240VE; TAD1241VE; TAD1242VE; TAD1250VE; TAD1251VE; TAD1252VE

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8221 Lifting Sling 2
B 8T-3052 Degree Wheel 1
C 8T-5096 Dial Indicator Gp 1
- Magnetic Base and Stand 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the crankshaft and inspect the crankshaft for wear and damage. Refer to Specifications, "Crankshaft" for more information. If necessary, replace the crankshaft or recondition the crankshaft.
If necessary, install the crankshaft gear. Refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install" for the correct procedure.
If necessary, install a new crankshaft timing ring. Refer to Disassembly and Assembly, "Crankshaft Timing Ring - Remove and Install" for the correct procedure.
Ensure that parent bores for bearing shells in the cylinder block are clean. Ensure that the threads for the main bearing bolts in the cylinder block are clean and free from damage.
Clean the main bearing shells and the thrust washers. Inspect the main bearing shells and the thrust washers for wear and damage. If necessary, replace the main bearing shells and the thrust washers. Note: If the main bearing shells are replaced, check whether oversize main bearing shells were previously installed. If the thrust washers are replaced, check whether oversize thrust washers were previously installed.
Illustration 1 g03412933
Install upper main bearing shells (11) to the cylinder block. Ensure that the locating tabs for the upper main bearing shells are seated in the slots in the cylinder block. Note: The upper main bearing shells have a groove and two oil holes.
Lubricate upper main bearing shells (9) with clean engine oil.
Illustration 2 g03412936
Attach Tooling (A) and a suitable lifting device to crankshaft (8). Lift crankshaft (10) into the cylinder block. The weight of the crankshaft is approximately 61 kg (134 lb). Note: Do not damage any of the finished surfaces on the crankshaft. Do not damage the main bearing shells.
Illustration 3 g03412932
Lubricate thrust washers (9) with clean engine oil. Install thrust washers (9) into number six main bearing in the cylinder block. Note: The grooves in the thrust washers must be located against the crankshaft. The thrust washers have a locating tab at one end. Ensure that the locating tabs are correctly seated in the cylinder block.
Illustration 4 g03412931
Install lower main bearing shells (8) into main bearing caps (7). Ensure that the locating tabs for the lower main bearing shells are correctly seated into the slots in the bearing caps. Note: The lower main bearing shells are plain bearings that do not have oil holes.
Lubricate lower main bearing shells (8) and lubricate the journals of the crankshaft with clean engine oil. Install main bearing caps (7) to the cylinder block. Note: Ensure the correct location and orientation of main bearing caps (7). The locating tabs for the upper and the lower main bearing shells should be on the same side of the engine.
Illustration 5 g03412935
Lubricate the threads of bolts (6) with clean engine oil. Lubricate the underside of the heads of bolts (6) with clean engine oil.
Install bolts (6) to main bearing caps (7). Evenly tighten the bolts in order to pull the caps into position. Ensure that the caps are correctly seated. Note: Do not tap the main bearing caps into position as the bearing shells may be dislodged.
Tighten bolts (6) to a torque of 80 N m (59 lb ft). Turn bolts (4) through an additional 90 degrees. Use Tooling (B) to achieve the final torque.
Rotate the crankshaft in order to ensure that there is no binding.
Illustration 6 g01399694
Check the crankshaft end play. Push the crankshaft toward the front of the engine. Install Tooling (C) to the cylinder block and the rear face of the crankshaft. Push the crankshaft toward the rear of the engine. Use Tooling (C) to measure the crankshaft end play. The permissible crankshaft end play is 0.10 mm (0.004 inch) to 0.41 mm (0.016 inch).
Illustration 7 g03412929
If necessary, follow Step 17.a through step 17.d to install cross over tube assembly (1).
Install new gasket (4) and new gasket (5).
Position cross over tube assembly (1) onto the cylinder block.
Install bolts (2) and bolts (3) to cross over tube assembly (1) finger tight.
Tighten bolts (2) and bolts (3) to a torque of 22 N m (195 lb in).
If the crankshaft has not been replaced or the crankshaft has not been reconditioned, install the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Install" for the correct procedure. End By:
If necessary, install the pistons and connecting rods. Refer to D


Parts hose Volvo Penta:

853012
Hose clamp
853012 Hose clamp
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131
943473
Hose clamp
943473 Hose clamp
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D12D-A MG; D12D-E MG, D3-110I-A; D3-110I-B; D3-110I-C, D42A; D42A PP, D5A-T; D5A-TA
942707
 
942707 Hose
AD31L-A; AD31P-A; AD41L-A, AQD70D; TAMD70D; TAMD70E, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, KAD32P; TAMD42WJ-A; KAD43P-A, MD22L; MD22P; MD22L-B, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD1030GE; TAD1031GE; TAD1032GE, TAD1230G;
1544733
 
1544733 Hose clamp
1372, D11A-A; D11A-B; D11A-C, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, DH10A; DH10A 285; DH10A 360, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD103
1674223
Hose clamp
1674223 Hose clamp
1372, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, TAD1030GE; TAD1031GE; TAD1032GE, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE,
949931
Hose
949931 Hose
1372, D13C1-A MP; D13C2-A MP; D13C3-A MP, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1340VE; TAD1341VE; TAD1342VE, TAD1341GE; TAD1342GE; TAD1343GE, TAD1350VE, TAD1351VE; TAD1352VE; TAD1353VE,
20435760
Hose clamp
20435760 Hose clamp
1372, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1030GE; TAD1031GE; TAD1032GE, TAD1240GE; TAD1241GE; TAD1242GE, TAD1340VE; TAD1341VE; TAD1342VE, TAD1341GE; TAD1342GE; TA
977651
 
977651 Hose assembly
TAD1030P, TAD1230P; TD121GP-87; TWD1210P, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD121G-87; TWD1210V; TWD1211V, TD610M; TD630ME; TWD630ME, TD610V; TWD610V; TD630VE, TD61A; TD61AW; TD61ACE, TD71A; TID71A; TWD710V, TWD1230ME, TW
Back to top