815343 Hose Volvo.Penta
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
Hose
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$22.99
01-09-2017
.13[0.00] pounds
Top of the: Top of the World
Stanford Cardinal Official NCAA Cuffed Knit Belowzero Beanie Stocking Stretch Sock Hat Cap by Top of the World 815343
Officially licensed by the Stanford Cardinal||Officially licensed by the NCAA||Top quality manufactured by Top of the World
Officially licensed by the Stanford Cardinal||Officially licensed by the NCAA||Top quality manufactured by Top of the World
Compatible models:
D100A; D100AK; D100B
TD100G; TD100G-85; TD100G-87
Volvo.Penta
Volvo Penta entire parts catalog list:
- Clutch: 813696 » 815343
- Clutch: 813695
Information:
Illustration 1 g02291594
Schematic for the circuit of the actuator for the bypass valve
Test Step 1. Inspect the Electrical Connectors and Wiring
Remove the electrical power from the engine. Note: For the following steps, refer to Troubleshooting, "Electrical Connectors - Inspect".
Thoroughly inspect each of the following connectors:
J1/P1 connectors
J9/P9 connectors
Connectors on the actuator for the bypass valve
Check the torque of the allen head screw for the ECM connectors.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the actuator for the bypass valve.
Illustration 2 g00935459
Right side views
Check the wiring for abrasion and for pinch points from the actuator for the bypass valve to the ECM. Expected Result:All of the connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - The components are in good condition with proper connections. Proceed to Test Step 2.
Not OK - The components are not in good condition and/or at least one connection is improper.Repair: Perform the necessary repairs and/or replace parts, if necessary. Ensure that all of the seals are properly installed. Ensure that the connectors are properly engaged. Verify that the repair has eliminated the original problem.STOPTest Step 2. Check for a Diagnostic Code
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Switch the 35 amp circuit breaker ON. Set the engine control to the STOP mode.
Use Cat ET in order to determine if one of the following diagnostic codes is active:
1720-9 Turbocharger Compressor Bypass Valve Actuator : Abnormal Update Rate
1720-11 Turbocharger Compressor Bypass Valve Actuator invalid
1720-12 Turbocharger Compressor Bypass Valve Actuator : FailureExpected Result:None of the diagnostic codes are active.Results:
OK - None of the diagnostic codes are active. The communication between the ECM and the actuator for the bypass valve appears to be OK at this time. However, diagnostic codes may be logged.Repair: If you are troubleshooting an intermittent problem, refer to Troubleshooting, "Electrical Connectors - Inspect".Terminating resistors must be connected to each end of the CAN data link. The terminating resistors improve the communication between the devices. If there is an intermittent diagnostic code for any of the devices that are connected to the CAN data link, be sure to check the terminating resistor that is on the right side of the terminal box. Also check the terminating resistor that is located on the right front side of the engine. The resistor will be near the compressor bypass valve. Replace parts, if necessary.STOP
Not OK (Active 1720-9) - The ECM has detected a problem with the communication between the ECM and the actuator for the bypass valve. Proceed to Test Step 3.
Not OK (Active 1720-11) - There is an active 1720-11 diagnostic code. This code indicates a problem with the movement of the actuator for the compressor bypass.Repair: The actuator for the compressor bypass valve must be installed properly in order to provide stable operation. If the motion is sticky and/or rough, investigate the cause of the binding. Perform the necessary repairs.STOP
Not OK (Active 1720-12) - There is an active 1720-12 diagnostic code.Repair: The actuator for the bypass valve has detected an internal fault. Replace the actuator. Verify that the repair has eliminated the original problem.STOPTest Step 3. Check for Electrical Power at the Actuator
Illustration 3 g01234707
Locations for the voltage check at the power distribution box
Refer to Illustration 3. Measure the voltage at the power distribution box.
Disconnect the electrical connector from the actuator.
Illustration 4 g01963093
Harness connector
Measure the voltage between terminals "Z" and "Q" at the harness
Parts hose Volvo Penta:
961653
961653 Hose nipple, heather outlet
2001; 2001B; 2001AG, D100A; D100AK; D100B, TAD1230P; TD121GP-87; TWD1210P, TD120HP-86; TD121; TD121G, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83, TD610M; TD630ME; TWD630ME, TD610V; TWD610V; TD630VE, TD61A; TD61AW; TD61ACE, TD71A; TID71A; TWD
943480
943480 Hose clamp
430; 430A; 430B, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D12D-A MG; D12D-E MG, D16C-A MG, D3-110I-A; D3-110I-B; D3-110I-C, D42A; D4
943473
943473 Hose clamp
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D12D-A MG; D12D-E MG, D3-110I-A; D3-110I-B; D3-110I-C, D42A; D42A PP, D5A-T; D5A-TA
192618
192618 Hose
AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQD70D; TAMD70D; TAMD70E, D1-13; D1-13B; D1-20, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D2-55; D2-55B; D2-55C, D2-7
943484
943484 Hose clamp
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70
961656
961656 Hose nipple
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TD100G; TD100G-85; TD100G-87, TD120HP-86; TD121; TD121G, TD120HPP; TID120HPP
87970
87970 Hose assembly
D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, TD100G-87; TD1030ME; TWD1030ME, TD100G; TD100G-85; TD100G-87, TD61A; TD61AW; TD61ACE
945754
945754 Hose clamp
D70B; D70B PP; D70B K, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAMD61A; TAMD62A, TAMD63L-A; TAMD63P-A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD72P-A; TAMD72WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TD100G-87;