3812561 Volvo.Penta Housing

Illustration 1 g00783070
(1) Vent hole (2) Hose clamp (3) Bolts that hold the breather assembly (4) Hose clamp (5) Breather assembly (6) Hose clamp
Ensure that the components of the breather assembly are installed in the correct positions. If not installed correctly, engine damage can result.
Note: Keep the area around vent hole (1) clean. Do not restrict the vent hole.
Loosen hose clamps (2), (4), and (6). Remove the hoses from the breather assembly (5) .
Remove two bolts (3) that hold the breather assembly (5) to the cylinder block. Remove the breather assembly (5) from the engine.
Discard the breather assembly (5). Install a new breather assembly by using the two bolts (3). Refer to the Operation and Maintenance Manual, "Torque Specifications" for the correct torques.
Install the hoses and tighten the hose clamps (2), (4), and (6). Refer to the Operation and Maintenance Manual, "Standard Torque for Constant Torque Hose Clamps" for the correct torques. 3056 Marine Engine
Turbocharged Engines
Illustration 2 g00749578
(1) Valve (2) Clips (3) Element (4) Clip retainers (5) Baffles (6) Gasket (7) ElbowThe crankcase breather removes the combustion gases from the engine crankcase. The crankcase breather directs the gases to the induction system.An internal port in the rocker cover allows the gases in the crankcase to pass into the breather body through an element (3). The gases flow through a series of baffles (5) and into the valve cover through holes at the bottom of the chamber for the baffles. Valve (1) controls the flow of gases which pass from the breather through the plastic outlet elbow (7) to the intake manifold.The valve cover and the breather assembly are made of a composite material. The valve cover and the breather assembly should be removed and installed with care.Disassembly
Do not use excessive force to remove the hose from the breather outlet elbow. If the breather outlet elbow breaks away from the breather body, see the procedure to repair the connection for the breather outlet elbow.
Release the hose clamp and carefully remove the hose from elbow (7) .
Remove the valve cover. Refer to the Service Manual for more information.
Use care not to damage the breather cover or the breather body with a pry bar.
Remove the bolts and carefully remove the breather cover from the breather body. It may be necessary to use a suitable pry bar in order to remove the breather cover from the breather body. Ensure that the pry bar does not damage the breather cover or the breather body. Gasket (6) should be removed and discarded.
Release clip retainers (2) on valve (1). Push valve (1) out of the breather cover.
Element (3) should be removed and discarded.
To prevent damage to the breather valve, remove the breather valve before the cover is washed.
Ensure that all the cleaning fluid is removed before the breather is assembled.
Use a clean nonflammable solvent to wash the body of the breather, the cover, baffle (5), and elbow (7). Thoroughly dry the components after cleaning the components.
Ensure that the holes in the bottom of the chamber for baffles (5 ) are not restricted. If necessary, clean the holes.Assembly
Install baffles (5) into the grooves in the breather body.
Install a new element (3) into the breather body.
Install a new valve (1) into the breather cover. Ensure that clip retainers (2) are engaged correctly.
Install a new gasket (6). The gasket is installed dry. Put the cover and valve assembly into position on the breather body. Loosely install the bolts. Tighten the bolts gradually and tighten the bolts evenly to a torque of 3 N m (27 lb in).
Do not use excessive force to fit the hose to the breather outlet elbow.
Ensure that there is no restriction in elbow (7) or in the breather hose. Carefully install the breather hose on elbow (7). Tighten the hose clamps that fasten the hose to the elbow.Procedure to Repair the Connection for the Outlet Elbow of the Breather
If the outlet elbow for the crankcase breather breaks, then use the following procedure in order to repair the elbow.
Thoroughly clean the inside of the breather body after it has been drilled.
Ensure that the breather body is secure. Use a 22.5 mm (0.89 inch) drill in order to drill to a depth of 10.0 mm (0.39 inch). Drill the depth in order to remove the broken connection of the outlet elbow. Thoroughly clean the inside of the breather body.
Thoroughly clean the contact faces of the elbow (7) and the breather cover.
Install elbow (7). Ensure that the contact surface of the connection for the elbow has a rough finish. Put the elbow into position on the breather body.
Apply Permabond® E3524 adhesive. Refer to the instructions on the adhesive. The adhesive will secure the elbow to the breather body.Naturally Aspirated Engines