872608 Volvo.Penta Hub

Table 1
Diagnostic Trouble Codes
CDL Code J1939 Code Code Description
(code descriptions may vary) Comments
E593 (2) 3711-31 Aftertreatment Insufficient Temperature to Complete Regeneration Active regeneration failed due to an inability of the Diesel Particulate Filter (DPF) to reach a high enough temperature. The code is logged. Engine power is derated.
Follow the troubleshooting procedure in order to identify the root cause of the problem. Illustration 1 and Illustration 2 show the location of the components for the ARD system.
Illustration 1 g01985013
ARD combustion head (typical)
(1) Flame detection temperature sensor
(2) Port for the heated nozzle
(3) ARD pilot filter connector
(4) ARD main filter connector
(5) ARD combustion head
(6) Inlet for the combustion air
Illustration 2 g02225997
CEM (typical)
(7) Combustion air valve
(8) Combustion air valve inlet
(9) Combustion air actuator
(10) ARD ignition coil
(11) Combustion air absolute pressure sensor
(12) Combustion air valve controller
(13) Differential pressure sensor
(14) Fuel filter fitting
(15) Cable for CEM connection to the engine
(16) Pilot fuel control valve
(17) Main fuel control valve
(18) Pilot fuel pressure sensor
(19) Main fuel pressure sensor
(20) Combustion air piping
(21) ARD combustion head
(22) Combustion air inlet to ARD combustion head
Table 2
Associated Diagnostic Trouble Codes
102-18
2489-13
3487-13
3480-15
3480-16
3480-17
3480-18
3556-7
4077-15
4077-16
4077-17
4077-18
E1050
E1051
E1052
E1053
Table 3
Troubleshooting Test Steps Values Results
1. Check for Associated Diagnostic Trouble Codes
A. Establish communication between Cat ET and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Table 2 lists the diagnostic trouble codes that are associated with the E593 (2) or 3711-31 code. Determine if any of the codes in Table 2 are present.
Diagnostic code
Result: An associated diagnostic trouble code is not present.
Proceed to Test Step 2.
Result: An associated diagnostic trouble code is present.
Troubleshoot the associated diagnostic code.
2. Check the Current Flow Through the Heater
A. Verify that the engine is off. Check the current flow through the heater. Refer to Systems Operation/Testing and Adjusting, "ARD Nozzle Heater - Test" for the correct procedure.
Between 7.0 A and 14 A for a 12 V system. Or, between 3.5 A and 7 A for a 24 V system
The current flow is between 7.0 A and 14 A for a 12 V system. Or, the current flow is between 3.5 A and 7 A for a 24 V system.
Result: The current flow is OK.
Proceed to Test Step 3.
Result: The current flow is not between 7.0 A and 14 A for a 12 V system. Or, the current flow is not between 3.5 A and 7 A for a 24 V system.
There may be a problem with the ARD nozzle. Refer to Troubleshooting, "ARD Nozzle - Test".
3. Inspect the Tubing between the Compressor and the Combustion Air Valve
A. Inspect the tube between the compressor and the combustion air valve.
B. Check for cracks in the tubing.
C. Check for loose hardware or damaged hardware.
Tubing
Result: The tube is not damaged or cracked.
Proceed to Test Step 4.
Result: The tube is damaged or cracked.
Repair: Replace the tubing or repair the tubing.
Proceed to Test Step 5.
4. Inspect the Tubing from the Combustion Air Valve to the Combustion Air Absolute Pressure Sensor
A. Inspect the tubing from the combustion air valve to the combustion air absolute pressure sensor.
B. Check for cracks in the tubing.
C. Check for air leaks.
D. Check the clamps on the tube. Make sure that the clamps are tight.
Tubing
Result: The tube is damaged or cracked.
Repair: Replace the tubing or repair the tubing.
Proceed to Test Step 5.
Result: The tube is not damaged.
Repair: Replace the combustion air valve. Refer to Disassembly and Assembly, "Air Control Valve - Remove and Install".
Proceed to Test Step 5.
Table 4
Troubleshooting Test Steps Values Results
5. Perform the "ARD Air System Service Test"
A. Reset all active codes and clear all logged codes. Use Cat ET to perform an "ARD Air System Service Test" to verify that the problem is resolved.
ARD Air System Service Test
Result: The "ARD Air System Service Test" passed.
Proceed to Test Step 6.
Result:The "ARD Air System Service Test" failed.
Repair: There is a problem with the ARD combustion air system. Refer to Troubleshooting, "ARD Combustion Air - Test"
6. Perform a "Manual DPF Regeneration"
This test must be performed through Cat ET. The Cat ET service tool enhances the diagnostics during the service test.
A. Clear all diagnostic codes.
B. Click the "Disconnect" icon on Cat ET in order to disconnect Cat ET from the engine ECM.
C. Turn the keyswitch to the Off position. Wait for five seconds.
D. Turn the keyswitch to the On position.
E. Click the "Connect" icon on Cat ET in order to connect Cat ET to the engine ECM.
F. Start the engine. Allow the engine to idle for three minutes.
Do not use the operators switch for a stationary regeneration. The service tests provide enhanced diagnostics that are necessary for proper troubleshooting and repair.
G. Start a "Manual DPF Regeneration" in Cat ET.
The ECM tests the nozzles for plugging after the "Manual DPF Regeneration" is complete. Approximately 10 minutes are required in order for the test to provide a result. A code will become active if the nozzles are plugged.
Manual DPF Regeneration
Result: The "Manual DPF Regeneration" completed successfully. There are no additional codes.
Return the unit to service.
Result: The "Manual DPF Regeneration" did not complete successfully.
Check the list of active diagnostic codes. Troubleshoot the code that applies to the failed regeneration. Refer to Table 2 for associated