846138 Volvo.Penta Injection pump


846138 Injection pump Volvo.Penta MD70C; TMD70C; TAMD70C Injection
846138 Injection pump Volvo Penta
Rating:
48

Buy Injection pump 846138 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Volvo Penta entire parts catalog list:

MD70C; TMD70C; TAMD70C; THAMD70C; AQD70BL; AQD70CL

Information:

start by: a) remove fuel injection pump housing and governorb) remove adapter housing
TYPICAL EXAMPLE1. Put the fuel injection pump housing and governor in position on tool (A).
TYPICAL EXAMPLE2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing.3. Remove governor housing (2).4. Remove two bolts (3) from the cover. Remove cover (4) from over the torque spring. 5. Remove spring (7), wave washer (6) and guide (5) from the governor housing.6. Remove gasket (8) from the governor housing. 7. Remove bolt (11) and nut (9) from the torque spring (10). Remove the torque spring.8. Remove pin (12) from the hole in the fuel injection pump housing. 9. Remove seat (15) and over fueling spring (16) from the shaft.10. Pull shaft (13) up and remove lever (14). 11. Remove riser (follower) (18) from the shaft.12. Remove ring and lever (17) from the dowel. 13. Remove cover (19) with tool (B). Tool (B) can cause damage to cover. Always inspect the cover for damage and install a new cover if needed. 14. Install timing pin (20) to hold the camshaft from turning.15. Remove three bolts (21) that hold the flyweight assembly in position.16. Remove flyweight assembly (22).17. Remove the timing pin from the fuel injection pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before the flyweight assembly is installed.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to overspeed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing.
TYPICAL EXAMPLE15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by: a) install adapter housingb) install fuel injection pump housing and governor


Parts injection Volvo Penta:

837514
 
837514 Injection pump
AQD70D; TAMD70D; TAMD70E, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
843026
Injection pump
843026 Injection pump
MD70C; TMD70C; TAMD70C
844442
Injection pump
844442 Injection pump
D70CHC; D70CRC; TD70CHC, MD70C; TMD70C; TAMD70C
844056
Injection pump
844056 Injection pump
MD70C; TMD70C; TAMD70C, TD70G; TD70G-83; TD70GPP
845275
 
845275 Injection pump
D70CHC; D70CRC; TD70CHC, MD70C; TMD70C; TAMD70C, TD70G; TD70G-83; TD70GPP
3803762
 
3803762 Injection pump, exch
D70CHC; D70CRC; TD70CHC, MD70C; TMD70C; TAMD70C, TD70G; TD70G-83; TD70GPP
845382
 
845382 Injection pump
MD70C; TMD70C; TAMD70C, TD70G; TD70G-83; TD70GPP
846139
 
846139 Injection pump
MD70C; TMD70C; TAMD70C
Back to top