3580503 Volvo.Penta Inlet manifold


3580503 Inlet manifold Volvo.Penta MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B Inlet
3580503 Inlet manifold Volvo Penta
Rating:
88

Buy Inlet manifold 3580503 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$216.98
 

28-12-2022

-: -
Triumph Sports 2x4 LED Cornhole Set with Integrated Caddy, Brown (35-8050-3)
Each caddy features two cup holders to hold various sized cans, bottles, and tumblers along with a caddy shelf to hold phones, keys, wallets, or bags and integrated scorekeeper || Play like the pros with this regulation size cornhole set and (8) 16oz Slick n Stick bags || Keep playing long after the sun goes down with the built-in LED lights to illuminate the entire play surface || Integrated caddy system is conveniently attached within each 2x4 cornhole board to easily rotate out for game play and in for storage || No assembly and no tools required. Set up in 60 seconds and you’re ready to play!
Number on catalog scheme: 1
 

Volvo Penta entire parts catalog list:

MD2010-C; MD2010-D; MD2020-C; MD2020-D; MD2030-C; MD2030-D; MD2040-C; MD2040-D; 120S-D; 120S-E
MD2010A; MD2020A; MD2030A; MD2040A; MS2B-R; MS2A-D; MS2A-E; MS2L-D; MS2L-E; 120S-D; 120S-E; MD2010; MD2030; MD2040; MD2020
MD2010B; MD2020B; MD2030B; MD2040B; MS2L-D; MS2A-D; 120S-D; MS2B-R; MS2A-E; MS2L-E

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 Thread Lock 1
B - Loctite 275 Thread Lock 1
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03343543Note: The position of fuel screw (17) controls the emissions of the engine. Ensure correct adjustment of the fuel screw. Refer to Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
If the original housing has been replaced with a new housing, follow Step 1.a through Step 1.e in order to install fuel screw (17).
Install fuel screw (17) to housing (3).
Install a new sealing washer (18) to fuel screw (17).
Loosely install locknut (19) to fuel screw (17). The procedure that is used to set the position of the fuel screw is described in Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
Do not install the tamper proof cap (20) until fuel screw (17) adjustment has been completed.
Install a new emissions label to front housing (3).
Illustration 2 g03343542
Illustration 3 g03343540
Place lever assembly (12) in position in front housing (3) and install shaft (11). Note: Ensure the correct orientation of the lever assembly.
Install a new sealing washer (14) to the treads of shaft (11).
Install nut (15). Tighten the nut to a torque of 6 N m (53 lb in).
Connect spring (13) to front housing (3).
Install a new silicon rubber bung (16).
Illustration 4 g03343538
If the engine is equipped with an angleich unit, follow Steps 7.a and 7.b in order to install the angleich unit.
Apply Tooling (B) to the first two threads of angleich unit (10).
Install angleich unit (10) to lever assembly (7). Tighten the angleich unit to a torque of 6 N m (53 lb in). Note: Ensure that Tooling (B) is not allowed to contaminate the plunger assembly of the angleich unit. Contamination of the plunger assembly will render the angleich unit inoperative.
Illustration 5 g03343536
Install a new sealing washer (8) to shaft (9).
Apply Tooling (A) to the first two threads of shaft (9).
Place lever assembly (7) in position in front housing (3) and install shaft (9). Tighten the shaft to a torque of 16 N m (142 lb in). Note: Ensure the correct orientation of the lever assembly.
Illustration 6 g03343535
Position a new gasket (6) (not shown) onto throttle control (1).
Position the assembly of throttle control (1) into front housing (3).
Install bolts (5). Tighten the bolts to a torque of 10 N m (89 lb in).
Illustration 7 g03343534
Install spring (4).
If the position of the fuel screw has been altered, the fuel screw must be reset. Refer to Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) Install" for the correct procedure.
After fuel screw (17) has been adjusted, to the procedure in Systems Operation, Testing and Adjusting, "Governor - Adjust". Install a new tamper proof cap (20) to nut (19). Refer to Illustration 1.


Parts inlet Volvo Penta:

3580478
 
3580478 Inlet valve
D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
861858
 
861858 Inlet valve
MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
3580303
 
3580303 Inlet valve
MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
Back to top