4804109 Volvo.Penta Inlet manifold


4804109 Inlet manifold Volvo.Penta TD30A; TD31ACE; TD40A Inlet
4804109 Inlet manifold Volvo Penta
Rating:
43

Buy Inlet manifold 4804109 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Volvo Penta entire parts catalog list:

TD30A; TD31ACE; TD40A; TD45B; D45A

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the bridge for the inlet valves. Valve lash is measured between the rocker arm and the valve stem for the exhaust valve. All of the clearance measurements and the adjustments must be made with the engine stopped. The valves must be fully closed.Valve Lash Check
An adjustment is not necessary if the measurement of the valve lash is in the acceptable range. Adjust the valve lash while the engine is stopped. The range is specified in Table 1.
Table 1
Inlet Valves Exhaust Valves
Valve Lash Check (Stopped Engine) 0.38 0.08 mm (0.015 0.003 inch) 0.64 0.08 mm (0.025 0.003 inch)
TC Compression Stroke 1-2-4 1-3-5
TC Exhaust Stroke(1) 3-5-6 2-4-6
Firing Order 1-5-3-6-2-4(2)
(1) 360° from TC compression stroke
(2) The No. 1 cylinder is at the front of the engine.If the measurement is not within this range adjustment is necessary. See Testing And Adjusting, "Valve Lash And Valve Bridge Adjustment".
Illustration 1 g01320108
Cylinder and Valve Location
(A) Exhaust valve
(B) Inlet valves Valve Lash and Valve Bridge Adjustment
Illustration 2 g01109236
(1) Exhaust rocker arm
(2) Inlet valve bridge
(3) Rocker arm adjustment screw locknut for the exhaust rocker arm
(4) Rocker arm adjustment screw for the exhaust rocker arm
Table 2
Valve Lash
Valves Dimension of Gauge
Inlet 0.38 0.08 mm (0.015 0.003 inch)
Exhaust 0.64 0.08 mm (0.025 0.003 inch) Adjust the valve lash while the engine is stopped.
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Table 3
TC Compression Stroke Inlet Valves Exhaust Valves
Valve lash 0.38 0.08 mm (0.015 0.003 inch) 0.64 0.08 mm (0.025 0.003 inch)
Cylinders 1-2-4 1-3-5
Adjust the valve lash according to Table 3.
Lightly tap the rocker arm at the top of the adjustment screw with a soft mallet. This will ensure that the lifter roller seats against the camshaft's base circle.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge.
Tighten the adjustment locknut to a torque of 30 7 N m (22 5 lb ft). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut.
Remove the timing bolt and turn the flywheel by 360 degrees in the direction of engine rotation. This will put the No. 6 piston at the top center position on the compression stroke. Install the timing bolt in the flywheel.
Table 4
TC Exhaust Stroke(1) Inlet Valves Exhaust Valves
Valve lash 0.38 0.08 mm (0.015 0.003 inch) 0.64 0.08 mm (0.025 0.003 inch)
Cylinders 3-5-6 2-4-6
(1) Position for No. 1 cylinder
Adjust the valve lash according to Table 4.
Lightly tap the rocker arm at the top of the adjustment screw with a soft mallet. This will ensure that the lifter roller seats against the camshaft's base circle.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the


Parts inlet Volvo Penta:

1542472
 
1542472 Inlet valve
AD30A; AQAD30A; MD30A, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A
838637
Inlet valve, intake
838637 Inlet valve, intake
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, TD30A; TD31ACE; TD40A, T
466379
Inlet valve
466379 Inlet valve
D70CHC; D70CRC; TD70CHC, MD70C; TMD70C; TAMD70C, TD30A; TD31ACE; TD40A, TD610G; TWD610G; TD710G, TD61A; TD61AW; TD61ACE, TD71A; TID71A; TWD710V, TWD610P; TWD610PB; TWD710P
7742050_078
7742050_079
7742050_080
7742050_081
838939
 
838939 Inlet pipe
TD30A; TD31ACE; TD40A
Back to top