876833 Volvo.Penta Intake gasket kit, induction manifold

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-3145     Load Leveling Beam     1    
6V-3144 Chain     2    
B     1U-5750     Engine Stand     1    
1U-5749 Adapter Plate     1    Start By:
Remove the engine hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
Remove the fan and the fan guard. Refer to Disassembly and Assembly, "Fan and Fan Guard - Remove and Install".Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes and for the purpose of orientation. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.Note: Put marks for orientation and location marks on all fittings for installation purposes.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.Remove the fill cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the approximate cooling system capacity. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the proper draining procedure.
Drain the hydraulic oil from the hydraulic tank into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the approximate amount of the hydraulic system oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the proper draining procedure.
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Recover the air conditioner refrigerant from the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
Illustration 1 g00814204
Disconnect hose assemblies (1) and (2) from the refrigerant compressor.
Illustration 2 g00818148
Note: The refrigerant accumulator must be removed in order to gain clearance for the installation procedure.Note: Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Remove refrigerant accumulator (3). Refer to Disassembly and Assembly, "Refrigerant Accumulator - Remove and Install".
Illustration 3 g00815210
Remove left side hood support bracket (4) .Note: It is not necessary to remove the right hood support bracket in order to remove the engine.