7744520_029 Volvo.Penta Leak-off line

Be sure the contact surfaces of the flywheel housing and the block are clean and free of any foreign material. Clean the contact surfaces with 8T9011 or 4C4079 Component Cleaner. Put an application of 1U8846 Gasket Maker on the contact surface of the flywheel housing. A 1.5 mm (.06 in) bead of 1U8846 Gasket Maker down the middle of the contact surface and around each bolt hole. Spread the bead of gasket maker into a thin even thickness over the contact surface.(1) Tighten flywheel housing bolts with the procedure that follows:a. Tighten bolts 1 through 24 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)b. Retighten bolts 1 through 24 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)(2) Maximum permissible change from an exact vertical face (face runout) at 4 points (total indicator reading) ... 0.38 mm (.015 in)(3) Torque for two plugs (Put 5P3413 Pipe Sealant on the threads at assembly) ... 9.5 1.5 N m (80 13 lb in) 8N5941, 101-9542 and 7C0366 flywheel housings, tighten the plug on the side of the flywheel housing to a torque of ... 55 14 N m (40 10 lb ft)7E8996 Flywheel Housing
Be sure the contact surfaces of the flywheel housing and the block are clean and free of any foreign material. Clean the contact surfaces with 8T9011 or 4C4079 Component Cleaner. Put an application of 1U8846 Gasket Maker on the contact surface of the flywheel housing. A 1.5 mm (.06 in) bead of 1U8846 Gasket Maker down the middle of the contact surface and around each bolt hole. Spread the bead of gasket maker into a thin even thickness over the contact surface.(1) Tighten flywheel housing bolts with the procedure that follows:a. Tighten bolts 1 through 22 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)b. Retighten bolts 1 through 22 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)6N9347 Flywheel Housing
Be sure the contact surfaces of the flywheel housing and the block are clean and free of any foreign material. Clean the contact surfaces with 8T9011 or 4C4079 Component Cleaner. Put an application of 1U8846 Gasket Maker on the contact surface of the flywheel housing. A 1.5 mm (.06 in) bead of 1U8846 Gasket Maker down the middle of the contact surface and around each bolt hole. Spread the bead of gasket maker into a thin even thickness over the contact surface.(1) Tighten flywheel housing bolts with the procedure that follows:a. Tighten bolts 1 through 24 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)b. Retighten bolts 1 through 24 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)6N2212 Flywheel Housing
Be sure the contact surfaces of the flywheel housing and the block are clean and free of any foreign material. Clean the contact surfaces with 8T9011 or 4C4079 Component Cleaner. Put an application of 1U8846 Gasket Maker on the contact surface of the flywheel housing. A 1.5 mm (.06 in) bead of 1U8846 Gasket Maker down the middle of the contact surface and around each bolt hole. Spread the bead of gasket maker into a thin even thickness over the contact surface.(1) Tighten flywheel housing bolts with the procedure that follows:a. Tighten bolts 1 through 20 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)b. Retighten bolts 1 through 20 in number sequence to a torque of ... 40 10 N m (29 7 lb ft)