954524 Volvo.Penta Lever

Table 1
Diagnostic Trouble Codes for the Motorized Valves
J1939 Code Description Notes
2791-6 Engine Exhaust Gas Recirculation (EGR) Valve Control : Current Above Normal The ECM detects a high current condition in the output for the EGR valve.
2791-7 Engine Exhaust Gas Recirculation (EGR) Valve Control : Not Responding Properly The ECM detects the signal from the EGR valve position sensor indicates that the valve is not in the desired position.
This diagnostic code can be caused by a loss of the 5 VDC supply to the EGR valve position sensor or a mechanical fault with the valve.
3464-6 Engine Throttle Actuator 1 Control Command : Current Above Normal The ECM detects a high current condition in the output for the engine intake throttle valve.
3464-7 Engine Throttle Actuator 1 Control Command : Not Responding Properly The ECM detects the signal from the intake throttle valve position sensor indicates that the valve is not in the desired position.
This diagnostic code can be caused by a loss of the 5 VDC supply to the intake throttle valve position sensor or a mechanical fault with the valve. The following background information is related to this procedure:NRS ValveThe NRS valve is used to control the amount of exhaust gas which is recirculated into the intake manifold.The amount of exhaust gas that is required is calculated by the software that is contained in the ECM. The NRS valve is controlled by a PWM signal from the ECM.Intake Throttle ValveThe intake throttle valve is used to increase the exhaust gas temperature to aid the regeneration process."Air System Motor Valve Verification Test"The "Air System Motor Valve Verification Test" will identify whether the NRS valve and the intake throttle valve are working correctly. This test must be performed when the engine speed is zero and the battery voltage is within an acceptable range. For a 12V system, the test must only be performed when the battery voltage is between 9V and 16V. For a 24V system, the test must only be performed when the battery voltage is between 18V and 32V. If the battery voltage is out of the required range, the test will be aborted.The "Air System Motor Valve Verification Test" will actively check position sensor diagnostics, motor short diagnostics, and motor open circuit diagnostics. The test will abort if any of these diagnostic codes become active.If the engine speed is not zero while the test is being performed, the test will be aborted. If no electrical diagnostic codes are active, the test will calibrate the NRS valve minimum position and the intake throttle valve minimum and maximum position. The test then moves the valves to various positions and checks the position sensor within each valve to confirm that the valve has responded correctly. Each valve will be tested in turn, starting with the NRS valve. If a test threshold is exceeded or any related diagnostic codes become active, the test will abort and generate a service tool error identifier.
Illustration 1 g06457321
Schematic diagram for the motorized valves
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect connectors for the motorized valves. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the engine interface connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Perform the "Air System Motor Valves Verification Test" and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly connected and/or inserted and the harness is free of corrosion, of abrasion or of pinch points.
Proceed to Test Step 2.
2. Check for Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
D. Monitor the electronic service tool for active diagnostic codes and/or logged diagnostic codes.
Diagnostic codes
Result: A -7 diagnostic code is active or recently logged for one or more of the motorized valves
Proceed to Test Step 3.
Result: A -6 diagnostic code is active or recently logged for one or more of the motorized valves.
Proceed to Test Step 8.
3. Measure the Sensor Supply Voltage at the Valve Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the suspect valve from the engine harness.
C. Turn the keyswitch to the ON position.
D. Measure the voltage at the harness