6210958 Volvo.Penta Lock ring

Table 1
Diagnostic Codes Table
Code Code Description Comments
95-2 Fuel Filter Differential Pressure Sensor : Erratic, Intermittent, or Incorrect The filtered fuel pressure is greater than the unfiltered fuel pressure. Ensure that the sensor connectors are connected to the correct sensors.
99-2 Engine Oil Filter Differential Pressure Sensor : Erratic, Intermittent, or Incorrect The filtered oil pressure is greater than the unfiltered oil pressure. Ensure that the sensor connectors are connected to the correct sensors.
100-3 Engine Oil Pressure Sensor Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
100-4 Engine Oil Pressure Sensor Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
101-3 Crankcase Air Pressure Sensor : Voltage Above Normal The code is logged. The value of the parameter is set to zero.
101-4 Crankcase Air Pressure Sensor : Voltage Below Normal The code is logged. The value of the parameter is set to zero.
110-3 Engine Coolant Temperature Sensor : Voltage Above Normal The code is logged. The value of the parameter is set to −40 °C (−40 °F).
110-4 Engine Coolant Temperature Sensor : Voltage Below Normal The code is logged. The value of the parameter is set to −40 °C (−40 °F).
172-3 Intake Manifold Air Temperature Sensor : Voltage Above Normal The code is logged. The value of the parameter is set to a default value.
172-4 Intake Manifold Air Temperature Sensor : Voltage Below Normal The code is logged. The value of the parameter is set to a default value.
274-3 Atmospheric Pressure Sensor Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
274-4 Atmospheric Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
289-3 Fuel Pressure Sensor - Before Fuel Filter : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
289-4 Fuel Pressure Sensor - Before Fuel Filter : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
460-3 Fuel Pressure Sensor - After Fuel Filter : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
460-4 Fuel Pressure Sensor - After Fuel Filter : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
542-3 Engine Oil Pressure Sensor - Before Oil Filter : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
542-4 Engine Oil Pressure Sensor - Before Oil Filter : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
827-3 Left Exhaust Temperature Sensor : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
827-4 Left Exhaust Temperature Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
828-3 Right Exhaust Temperature Sensor : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
828-4 Right Exhaust Temperature Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
829-3 Rear Aftercooler Coolant Temperature Sensor : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
829-4 Rear Aftercooler Coolant Temperature Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
1785-3 Intake Manifold Pressure Sensor Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
1785-4 Intake Manifold Pressure Sensor Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
2302-3 Engine Coolant Pump Outlet Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
2302-4 Engine Coolant Pump Outlet Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
2738-3 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
2738-4 Turbocharger #1 Compressor Inlet Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged.
2739-3 Turbocharger #2 Compressor Inlet Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is above normal . The code is logged.
2739-4 Turbocharger #2 Compressor Inlet Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is below normal . The code is logged. System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Engine oil pressure sensor
Barometric pressure sensor
Fuel pressure sensor
Intake manifold pressure sensorThe supply voltage is routed to terminal 1 of each sensor connector. The sensor return is routed to terminal 2 of each sensor connector. The sensor signal is routed to terminal 3 of each sensor connector. The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.The ECM performs an automatic calibration of these sensors whenever the ECM is powered and the engine is off for at least 5 seconds. During an automatic calibration, the ECM calibrates pressure sensors to the value of the atmospheric pressure at sea level. This calibration value is then checked against an acceptable offset pressure range.The ECM continuously outputs a pull-up voltage on the input terminal from an analog sensor. The ECM uses this pull-up voltage in order to detect an open or a short in the signal circuit. When the ECM detects the presence of a voltage that is above the normal range of the sensor on the signal circuit, the ECM will generate an open circuit diagnostic code -3 for that sensor. When the ECM