983789 Lock nut Volvo.Penta
XDP-B; TSK X-B; TSK X-BLT
Lock

Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$137.69
06-04-2023
-: -
Kimpex 13-897 Cover Trailerable Storage Ski-doo REV 2003 to 2014 Heavy Duty
Dimensions: Specific || Fits on: Ski-Doo || Color: Black || Material: 600D Polyester || Platform: REV
Dimensions: Specific || Fits on: Ski-Doo || Color: Black || Material: 600D Polyester || Platform: REV
Compatible models:
XDP-B; TSK X-B; TSK X-BLT
Volvo.Penta
Volvo Penta entire parts catalog list:
- Gimbal Ring » 983789
- Gimbal Ring
Information:
Illustration 1 g01341877
Typical example
Cut cable tie (3). Unscrew the fastener (6) that secures the OEM harness (2) to the electronic control module (5). Disconnect the OEM harness from the electronic control module.
Cut the cable straps (1), (9) and (10). Unscrew the fastener (8) that secures engine harness (7) to electronic control module (5). Disconnect the engine harness from the electronic control module.
Make temporary identification marks on plastic tube assemblies (4) and (11) in order to show the correct position of the tube assemblies.
Place a suitable container below the electronic control module (5) in order to catch any fuel that might be spilled.
Disconnect plastic tube assemblies (4) and (11). Plug the plastic tube assemblies with new plugs. Drain the fuel from electronic control module (5). Cap the connectors in the electronic control module with new caps.
Illustration 2 g01341878
Typical example
Loosen bolts (19) and remove the assembly of the electronic control module. Note the orientation of the electronic control module.
Remove bolts (19) and remove washers (18) from electronic control module (5). Note the position of the ground strap for the electronic control module.
If necessary, follow Steps 10.a through 10.d in order to disassemble the electronic control module.
Remove isolation mounts (20) and spacers (21).
Remove connectors (13). Remove the O-ring seals (12) from the connectors.
Remove torx screw (15) and remove bracket (14) for the engine wiring harness. Note the orientation of the bracket.
Remove bolt (17) and remove bracket (16) from the engine wiring harness. Note the orientation of the bracket. Installation Procedure
If a replacement electronic control module is installed, the module must be programmed with the correct information. Refer to Troubleshooting Guide, "Replacing the ECM" and refer to Troubleshooting Guide, "Flash Programming" for the correct procedure.
Ensure that the electronic control module is clean and free from damage. If necessary, replace the electronic control module.
Illustration 3 g01341878
Typical example
If necessary, follow Steps 3.a through 3.d in order to assemble the electronic control module.
Install new O-ring seals (12) to connectors (13). Install two connectors (13) to the electronic control module. Tighten the connectors to a torque of 18.5 N m (13.6 lb ft).
Position bracket (14) on the electronic control module. Ensure that the bracket is correctly oriented. Install torx screw (15). Tighten the torx screw to a torque of 20 N m (14 lb ft).
Position bracket (16) on electronic control module (5). Ensure that the bracket is correctly oriented. Install bolt (17). Tighten the bolt to a torque of 20 N m (14 lb ft).
Install isolation mounts (20) and spacers (21) to the electronic control module.
Install washers (18) and bolts (19) to electronic control module (5). Note: Ensure that the ground strap for the electronic control module is clamped between the washer and the appropriate bolt.
Install the assembly of the electronic control module to the mounting bracket. Tighten bolts (19) to a torque of 22 N m (16 lb ft). Note: Ensure that the electronic control module is correctly oriented. Ensure that the ground strap is not strained as the bolt is tightened.
Illustration 4 g01341877
Typical example
Remove the plugs from plastic tube assemblies (4) and (11). If necessary, remove the caps from the connectors in the electronic control module. Connect plastic tube assemblies (4) and (11).
Connect engine wiring harness (7) to electronic control module (5). Tighten the fastener (8) to a torque of 5 N m (3 lb ft). Note: Care must be taken in order to avoid damage to the connector pins during installation of the harness.
Position the assembly of the engine wiring harness onto brackets (14) and (16). Use new cable straps (1), (9) and (10) in order to secure the harness assembly to the brackets.
Connect OEM wiring harness (2) to electronic control module (5). Tighten fastener (6) to a torque of 5 N m (3 lb ft). Note: Care must be taken in order to avoid damage to the connector pins during installation of the harness.
Use a new cable strap (3) in order to secure the harness assembly.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime".
Parts lock Volvo Penta:
971089
971089 Lock nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ231A; AQ231B; AQ
963108
963108 Lock nut
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151
982531