3588346 Volvo.Penta Lubricant

Illustration 1 g00791619
Typical operating range of an oil temperature sensor
(1) In these areas, the output voltage of the sensor is too high or too low. The output is outside of the normal range. The electronic problem will generate a diagnostic code.
(2) In this area, the oil temperature above 102 °C (216 °F) is higher than normal. The output voltage of the sensor will generate an event code for a warning or a shutdown for high oil temperature. The sensor does not have an electronic problem.
(3) This area represents the normal operating temperature for the engine oil. The normal output voltage of the sensor is between 0.2 and 4.1 volts. The following format is used for event codes:
"EXXX (X) Description of the code"The "E" means that the code is an event code. The "XXX" represents a numeric identifier for the event code. The fourth "(X)" represents a numeric identifier for the severity of the code. This is followed by a description of the code. See the following example:
"E004 (3) Engine Overspeed Shutdown"The numbers that indicate the severity of the event code are defined below:Warning (1) - This condition represents a serious problem with engine operation. However, this condition does not require a shutdown.Shutdown (3) - For this condition, the engine is shut down in order to help prevent possible engine damage.These responses to certain events may be programmed into the ECM. If the responses are programmed, Cat ET can display the event. If the responses are not programmed, the display will not appear. However, the occurrence of any event will cause the event code to be logged in the ECM.Note: Do not confuse event codes with diagnostic codes. For information on diagnostic codes, see Troubleshooting, "Troubleshooting with a Diagnostic Code".Perform the following tasks before you troubleshoot the event code:
Gather enough information about the complaint in order to describe the symptom(s) adequately.
Verify that the complaint is not due to normal engine operation.
Repair all active diagnostic codes. See Troubleshooting, "Troubleshooting With A Diagnostic Code".Troubleshooting
For basic troubleshooting of the engine, perform the following steps first in order to diagnose a malfunction.
Gather information about the complaint from the operator.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
Connectors
Check the diagnostic codes and event codes. Repair any active codes. If these inspections do not reveal any problems, identify the probable causes with the procedures in this manual that best describe the symptoms. Check each probable cause according to the tests that are recommended.Be sure to check the connectors. This is specially true for problems that are intermittent. See Troubleshooting, "Inspecting Electrical Connectors".Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.Operator Information
Obtain the following information from the operator:
The occurrence and the time of the occurrence
Determine the conditions for the occurrence. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or the customer that could cause the symptom.
Determine whether any other occurrences happened in addition to the symptom.Diagnostic Codes and Event Codes
Examine the following information regarding any codes:
The probable cause of the symptom is correlated to the code.
The code was generated when the symptom occurred.
Codes that are repeatedly logged
The complaint is not due to normal engine operation.Other Symptoms
If other occurrences happened in addition to the symptom, investigate the following conditions:
The other occurrences are related to the symptom.
The symptoms have a probable cause that is common.Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.When an event code is active, the "Active Alarm" indicator ("Engine Control Alarm Status" on Cat ET) is activated in order to alert the operator. If the condition that generated the code is momentary, the message disappears. The event code will be logged in the ECM memory.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Logged Event Codes
When the ECM generates an event code the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when a code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeThis information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.A code is cleared from memory when one of the following conditions occur:
The service technician manually clears the code.
The code does not recur for 1000 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.Logged events are listed in chronological order. The most recent event code is listed first.Note: Always clear logged event codes after investigating and correcting the problem which generated the code.