183394 Needle bearing Volvo.Penta
AQ115A; AQ115B; AQ130
Needle
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$40.00
08-06-2024
US: XRmarine
GluckMarine 438592 Water Pump Rebuild Kit for Johnson Evinrude 25 28 30 35 40 48 50 HP Outboard 18-3454
GluckMarine This is Water Pump Impeller Rebuild Repair Kit for Johnson Evinrude OMC Marine Outboard Models || Replaces Johnson Evinrude 438592 433548 433549 777805 0433548 433549 0438592 777805 Sierra 18-3454 18-3394 Mallory Marine 9-48209 and GLM Marine 12245 || Compatible with Johnson Evinrude OMC 25 28 30 35 40 48 50 HP motors || Package contains 1X Impeller Assebbly 0432941 0437059 18-3104 1X Impeller Key 0334897 18-3138 1X Impeller Housing Assembly 0435594 1X Cup Impeller Housing 0340619 18-3455 1X Impeller Housing Plate 0319275 18-3126 1X Wear Plate Gasket 0336530 18-2709 1X Seal Housing 0324981 18-7481 2X Grommet 0333758 18-2708 18-2705 2X O Ring 0777973 18-7135 0331188 18-7143 4X Screws 331979 18-3133 || Impellers must be inspected at the beginning of each season. Look for signs of wear such as cracked or damaged blades to determine if they need to be replaced. Also, closely monitor the engine's water temperature. If you notice an increase in temperature, especially at low idle speeds, or a decrease in water flow as the engine reaches normal operating temperatures, this could indicate a clogged cooling outlet or a worn/damaged impeller
GluckMarine This is Water Pump Impeller Rebuild Repair Kit for Johnson Evinrude OMC Marine Outboard Models || Replaces Johnson Evinrude 438592 433548 433549 777805 0433548 433549 0438592 777805 Sierra 18-3454 18-3394 Mallory Marine 9-48209 and GLM Marine 12245 || Compatible with Johnson Evinrude OMC 25 28 30 35 40 48 50 HP motors || Package contains 1X Impeller Assebbly 0432941 0437059 18-3104 1X Impeller Key 0334897 18-3138 1X Impeller Housing Assembly 0435594 1X Cup Impeller Housing 0340619 18-3455 1X Impeller Housing Plate 0319275 18-3126 1X Wear Plate Gasket 0336530 18-2709 1X Seal Housing 0324981 18-7481 2X Grommet 0333758 18-2708 18-2705 2X O Ring 0777973 18-7135 0331188 18-7143 4X Screws 331979 18-3133 || Impellers must be inspected at the beginning of each season. Look for signs of wear such as cracked or damaged blades to determine if they need to be replaced. Also, closely monitor the engine's water temperature. If you notice an increase in temperature, especially at low idle speeds, or a decrease in water flow as the engine reaches normal operating temperatures, this could indicate a clogged cooling outlet or a worn/damaged impeller
$27.90
10-06-2024
CN: ninawesome
438592 Water Pump Impeller Repair Kit Compatible with Evinrude Johnson 40 45 48 50 HP Outboard Marine Motors with Housing Replacement for 18-3454 18-3394
ninawesome Replacement: 0438592, 0433548, 0433549, 0777805. Compatibale with Sierra Marine 18-3454 18-3394, Mallory Marine 9-48209, GLM Marine 12245, SEI Marine 96-364-01AK , OBR Red Rhino JE-222. || Fitment: for 25HP 28HP 30HP 35HP 40HP 48HP 50HP Evinrude Johnson OMC BRP marine outboard engines. || Package Contents: Neoprene Impeller 3 van, Wear Plate, Insert Cup, Water Pump Gasket, Key, "O"- Ring, Water Seal, Pump Housing, Crommet and Install Bolts as pictures showed. || High-quality replacement part, made of high-quality materials and fully tested to ensure long-term effective operation.Strength and toughness higher. || Customer satisfaction is our tireless pursuit.Whether it's a replacement or a full refund, we're dedicated to making your shopping experience absolutely risk-free.
ninawesome Replacement: 0438592, 0433548, 0433549, 0777805. Compatibale with Sierra Marine 18-3454 18-3394, Mallory Marine 9-48209, GLM Marine 12245, SEI Marine 96-364-01AK , OBR Red Rhino JE-222. || Fitment: for 25HP 28HP 30HP 35HP 40HP 48HP 50HP Evinrude Johnson OMC BRP marine outboard engines. || Package Contents: Neoprene Impeller 3 van, Wear Plate, Insert Cup, Water Pump Gasket, Key, "O"- Ring, Water Seal, Pump Housing, Crommet and Install Bolts as pictures showed. || High-quality replacement part, made of high-quality materials and fully tested to ensure long-term effective operation.Strength and toughness higher. || Customer satisfaction is our tireless pursuit.Whether it's a replacement or a full refund, we're dedicated to making your shopping experience absolutely risk-free.
TimotecMarine 438592 Water Pump Repair Kit for Johnson Evinrude 25 28 30 35 40 48 50 HP Outboard 18-3454
TimotecMarine This is water pump impeller repair kit for Johnson Evinrude OMC marine outboard motor || Compatible with Johnson Evinrude OMC 25 28 30 35 40 48 50 HP motors || Replaces Johnson Evinrude 438592 433548 433549 777805 0433548 433549 0438592 777805 Sierra 18-3454 18-3394 Mallory Marine 9-48209 and GLM Marine 12245 || Impellers need to be inspected at the beginning of each season. Look for signs of wear, such as cracked or damaged blades, to determine if they need to be replaced. Also, closely monitor your engine's water temperature. If you notice an increase in temperature (especially at low idle) or a decrease in water flow when the engine reaches normal operating temperature, this could indicate a clogged cooling outlet or a worn impeller. || Package contains 1X Impeller Assebbly 0432941 0437059 18-3104 1X Impeller Key 0334897 18-3138 1X Impeller Housing Assembly 0435594 1X Cup Impeller Housing 0340619 18-3455 1X Impeller Housing Plate 0319275 18-3126 1X Wear Plate Gasket 0336530 18-2709 1X Seal Housing 0324981 18-7481 2X Grommet 0333758 18-2708 18-2705 2X O Ring 0777973 18-7135 0331188 18-7143 4X Screws 331979 18-3133
TimotecMarine This is water pump impeller repair kit for Johnson Evinrude OMC marine outboard motor || Compatible with Johnson Evinrude OMC 25 28 30 35 40 48 50 HP motors || Replaces Johnson Evinrude 438592 433548 433549 777805 0433548 433549 0438592 777805 Sierra 18-3454 18-3394 Mallory Marine 9-48209 and GLM Marine 12245 || Impellers need to be inspected at the beginning of each season. Look for signs of wear, such as cracked or damaged blades, to determine if they need to be replaced. Also, closely monitor your engine's water temperature. If you notice an increase in temperature (especially at low idle) or a decrease in water flow when the engine reaches normal operating temperature, this could indicate a clogged cooling outlet or a worn impeller. || Package contains 1X Impeller Assebbly 0432941 0437059 18-3104 1X Impeller Key 0334897 18-3138 1X Impeller Housing Assembly 0435594 1X Cup Impeller Housing 0340619 18-3455 1X Impeller Housing Plate 0319275 18-3126 1X Wear Plate Gasket 0336530 18-2709 1X Seal Housing 0324981 18-7481 2X Grommet 0333758 18-2708 18-2705 2X O Ring 0777973 18-7135 0331188 18-7143 4X Screws 331979 18-3133
Number on catalog scheme: 6
Compatible models:
AQ115A; AQ115B; AQ130
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
2. Disconnect hose assembly (1). Cap and plug all openings immediately. 3. Cut tie wrap (2). 4. Remove four bolts and washers (3). Disconnect elbow assembly (4) from the sea water pump. 5. Remove gasket (5). 6. Remove four bolts and washers (7). Remove clip (6).7. Remove sea water pump (8). 8. Remove gasket (9).9. Remove four nuts and washers (10).10. Remove pump drive (11).11. Remove the O-ring seal from the pump drive. The following steps are for the installation of the sea water pump.12. Check the condition of the O-ring seal used on the pump drive. If necessary, replace with a new part. 13. Place pump drive (11) in position. Install four nuts and washers (10). Install a new gasket (9). 14. Place sea water pump (8) in position. Make sure the splined shaft on the sea water pump is in alignment with the coupling on the pump drive. Install clip (6) and four bolts and washers (7). 15. Install a new gasket (5). 16. Connect elbow assembly (4) and install four bolts and washers (3). 17. Install tie wrap (2). 18. Connect hose assembly (1).19. Fill the engine with coolant to the correct level. See the Operation & Maintenance Manual for this procedure.Disassemble & Assemble Sea Water Pump (JABSCO)
Start By:a. remove sea water pump 1. Remove four bolts and washers (1).2. Remove cover (2) from body (3). 3. Remove seal (4). 4. Remove impeller (5) and cam (6) from body (3). 5. Remove O-ring seal (7) and O-ring seal (8) from body (3).
There is spring force against spring seat (9). When retaining ring (10) is removed, the spring force will be released. To prevent possible personal injury, hold spring seat (9) in position as retaining ring (10) is slowly removed.
6. Remove retaining ring (10) with Tool (A).7. Remove spring seat (9) and spring (11). 8. Remove plate (12) from body (3). 9. Remove seal assembly (13) from body (3). If necessary, remove dowel (14). 10. Use Tool (B) to remove retaining ring (15) from housing (16). 11. Remove four bolts and washers (17). 12. Separate body (3) from housing (16). 13. Remove seal (18) from body (3) if necessary. 14. Remove O-ring seal (19).15. Use a soft hammer and tap shaft assembly (20) out of housing (16). 16. Remove shaft seal (21) from housing (16). 17. Use a press as shown to remove bearing (22) from shaft assembly (20). 18. Turn shaft assembly (20) over and use a press to remove bearing (23). The following steps are for the assembly of the sea water pump. 19. Heat bearings (22) and (23) to a temperature of 135 C° (275 F°) and install onto shaft assembly (20). 20. Install shaft seal (21) onto shaft assembly (20) as shown. 21. Install shaft assembly (20) in its original position in housing (16). (Tap lightly with a soft hammer). 22. Install seal (18) in body (3). 23. Position body (3) in its original position on housing (16). 24. Install four bolts and washers (17). 25. Use Tool (B) to install retaining ring (15) into housing (16). 26. Install seal assembly (13). If dowel (14) was removed, install the dowel into body (3). 27. Install plate (12) into body (3). Align the cut out in plate (12) to fit over dowel (14). 28. Install spring (11) and spring seat (9). 29. Apply enough pressure to spring seat (9) to compress spring (11). Install retaining ring (10) with Tool (A). 30. Install O-ring (7) and O-ring (8) as shown into body (3). 31. Install cam (6) and impeller (5) into body (3). 32. Install seal (4). 33. Position cover (2) onto body (3) and install four bolts and washers (1). Tighten bolts (1) to a torque of 9 N m (80 lb in).End By:a. install sea water pump
Start By:a. remove sea water pump 1. Remove four bolts and washers (1).2. Remove cover (2) from body (3). 3. Remove seal (4). 4. Remove impeller (5) and cam (6) from body (3). 5. Remove O-ring seal (7) and O-ring seal (8) from body (3).
There is spring force against spring seat (9). When retaining ring (10) is removed, the spring force will be released. To prevent possible personal injury, hold spring seat (9) in position as retaining ring (10) is slowly removed.
6. Remove retaining ring (10) with Tool (A).7. Remove spring seat (9) and spring (11). 8. Remove plate (12) from body (3). 9. Remove seal assembly (13) from body (3). If necessary, remove dowel (14). 10. Use Tool (B) to remove retaining ring (15) from housing (16). 11. Remove four bolts and washers (17). 12. Separate body (3) from housing (16). 13. Remove seal (18) from body (3) if necessary. 14. Remove O-ring seal (19).15. Use a soft hammer and tap shaft assembly (20) out of housing (16). 16. Remove shaft seal (21) from housing (16). 17. Use a press as shown to remove bearing (22) from shaft assembly (20). 18. Turn shaft assembly (20) over and use a press to remove bearing (23). The following steps are for the assembly of the sea water pump. 19. Heat bearings (22) and (23) to a temperature of 135 C° (275 F°) and install onto shaft assembly (20). 20. Install shaft seal (21) onto shaft assembly (20) as shown. 21. Install shaft assembly (20) in its original position in housing (16). (Tap lightly with a soft hammer). 22. Install seal (18) in body (3). 23. Position body (3) in its original position on housing (16). 24. Install four bolts and washers (17). 25. Use Tool (B) to install retaining ring (15) into housing (16). 26. Install seal assembly (13). If dowel (14) was removed, install the dowel into body (3). 27. Install plate (12) into body (3). Align the cut out in plate (12) to fit over dowel (14). 28. Install spring (11) and spring seat (9). 29. Apply enough pressure to spring seat (9) to compress spring (11). Install retaining ring (10) with Tool (A). 30. Install O-ring (7) and O-ring (8) as shown into body (3). 31. Install cam (6) and impeller (5) into body (3). 32. Install seal (4). 33. Position cover (2) onto body (3) and install four bolts and washers (1). Tighten bolts (1) to a torque of 9 N m (80 lb in).End By:a. install sea water pump
Parts needle Volvo Penta:
181359
181359 Needle roller assemb
430; 430A; 430B, 500; 500A; 501A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ
183391
183391 Needle roller bearin
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A
183497
183497 Needle bearing
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B
183390
183390 Needle roller bushin
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B
803474
181268
181268 Needle roller assemb
AQ115A; AQ115B; AQ130, MB10A, MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD21B; AQD21B, MD5A; MD5B; MD5C, MD6; MD6A; MD6B
813999
813999 Needle bearing
AQ115A; AQ115B; AQ130, MB10A, MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD5A; MD5B; MD5C, MD6; MD6A; MD6B
181288
181288 Needle bearing
AQ115A; AQ115B; AQ130, MB10A, MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD21B; AQD21B, MD5A; MD5B; MD5C, MD6; MD6A; MD6B