334274 Volvo.Penta Needle bearing


334274 Needle bearing Volvo.Penta D42A; D42A PP Needle
334274 Needle bearing Volvo Penta
Rating:
38

Buy Needle bearing 334274 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$107.45
 

09-01-2023
34.0[15.30] Pounds
-: -
SENSEN 1791 Front or Rear Struts Compatible with 2000-2002 Subaru Legacy Sedan
Cross Reference Number: 2701-248209, 2701-248279, 2701-248280, 331760L, 331760R, 345397, G56555, G56556, G56557, 334273, 334274, 341275, 71354, 71447, 71448
$56.99
 

09-01-2023

-: -
Maxorber Front Shocks Struts Absorber Kit Compatible with 2000 2001 2002 Subaru Legacy Sedan Front Shock AWD 334273 334274
ITEM-INCLUDED:Shocks kits (without strut mount,coil spring and rubber buffer).Please Double-Check the year,make,model,trim before purchasing. || SHOCK ABSORBER FITMENT:Front Set (2 pieces) of Struts for a 2000 2001 2002 Subaru Legacy Sedan AWD (Excludes Outback/Wagon Model). Cross reference numbers include KYB: 334273, 334274 || ADVANTAGES 100%:To get the best-rated shocks and struts for your car, shocks absorbers are made from strong,thick steel, reinforced with a chrome or zinc coating.Oil Seals,no squeaking noise,long durability. || INSTALLATION-EASILY--This is 100% tested auto shocks. The buckle holes are consistent with the original car in situ,so you can remove and replace it without take apart existing strut assembly or any other changes,quick installation. || SUGGESTION for REPLACE SHOCK ABSORBER:(1)Oil leakage.(2)Noise (rattling/knocking).(3)Poor driving performance.(4)Unusual wear patterns on the tire thread.(5)The car sink when the road is bad or load is heavy.
$88.43
 

09-01-2023
11.51[5.18] Pounds
-: -
KAYABA UK KYB334274 KYB 334274 Shock Absorber
KYB 334274 Shock Absorber || Kyb || Shock Absorbers
Number on catalog scheme: 24
 

Compatible models:

D42A; D42A PP   Volvo.Penta

Volvo Penta entire parts catalog list:

Information:

Probable Causes
Active codes and logged codes
Fuel system
Fuel injectorsRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if a code is active or logged.
Diagnostic code
Result: A code is active or logged.
Troubleshoot any active codes before continuing with this procedure.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. Check the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Inspect the fuel system for external leaks.
D. Check that there is no air in the clear primary fuel filter. Refer to Systems Operation/Testing and Adjusting, Low-Pressure System - Test.
E. Change the primary fuel filter and the in-line filter for the fuel transfer pump.
F. Check fuel quality. Refer to Testing and Adjusting, Fuel Quality - Test, for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
G. Check for the proper operation of the fuel transfer pump. Replace the pre-filter if excessive contamination or if the maintenance interval is exceeded. Refer to Testing and Adjusting, Low Fuel Pressure System-Test, for test information.
Fuel system
Result: The fuel system is OK.
Proceed to Test Step 3.
Result: The fuel system is not OK.
Replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
3. Fuel Injectors
A. If service has been performed on the engine fuel system recently, verify that the injector trim codes in the Engine ECM match the injector for each cylinder. If injectors were moved between cylinders or if an injector was replaced and the injector trim codes were not updated in the Engine ECM, this can cause an engine miss.
B. Access the "Cylinder Cutout Test" in the "Diagnostic Tests" under the "Diagnostics" menu. Cut out each cylinder one at a time to listen for improvements in the engine. If engine sound improves while cutting out a specific cylinder or cylinders, then check that the injector(s) are working properly by using 440-6907 Injector Kit .
Note: The injector deliver quantity is not a reliable indicator of a failed injector. It is not recommended to use that test in determining if an injector is failed.
Fuel Injectors
Result: If injector(s) trim codes for each cylinder do not match what is in the Engine ECM, then refer to Special Instruction, REHS9707, for the procedure to install the new injector QR codes within the Engine ECM and on-line. Confirm that this resolves the issue.
Result: If injector(s) are found to be defective, then replace the injector(s). Refer to Disassembly and Assembly, Electronic Unit Injector - Remove and Install. Refer to Special Instruction, REHS9707, for the procedure to install the new injector QR codes within the Engine ECM and online. Confirm that this resolves the issue.
Note: If two or more injectors are not working properly, this is likely a result of water in the fuel, bad fuel, or contaminated fuel. Contaminated fuel can occur by pre-filling the fuel filter or contamination during a previous repair of the fuel system. The root cause needs to be determined to prevent a repeat occurrence.
Result: There are no previous known services on fuel system and there was no noticeable improvement during the cylinder cut out test. The customer could have ordered injectors through parts and did not change the injector trim codes in the Engine ECM. Visually confirm that the injector trim code for each cylinder matches what is in the Engine ECM. Refer to Special Instruction, REHS9707, for the procedure to install the new injector QR codes within the Engine ECM and on-line.
The procedure corrected the issue. Return the engine to service.


Parts needle Volvo Penta:

243091
Needle bearing
243091 Needle bearing
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD1030G;
240453
Needle bearing
240453 Needle bearing
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B;
183235
350349
352303
183236
Back to top