396013 Volvo.Penta Nipple


396013 Nipple Volvo.Penta MD11; MD11C; MD11D, MD1B; MD2B; AQD2B Nipple
396013 Nipple Volvo Penta
Rating:
13

Buy Nipple 396013 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$6.55
 

06-02-2021

-: -
1961 Topps #427 Dick Ellsworth Cubs EX-MT/NR-MT 396013 Kit Young Cards
SELLER
$669.27
 

17-06-2023
22.0[9.90] Pounds
-: -
American Shifter 396013 Shifter Kit (PG 6" E Brake Cable Clamp Clevis Trim Kit Dipstick for D4F8F, 1 Pack)
Application : Powerglide || Shifter Style : Push Button Only || Shifter Arm Size : 6in Straight || Shifter Arm Finish : Chrome || Knob : Standard
Number on catalog scheme: 28
 

Compatible models:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8F-6123 Bolt 2
0S-1575 Bolt 4
3B-1925 Washer 4
C 8T-0455 Liner Projection Tool Group 1
D 2P-8260 Cylinder Liner Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Cylinder Liner Projection
Illustration 1 g01208517
Install a new gasket for the spacer plate and install the spacer plate.
Do not install the O-ring seals or the filler band on the cylinder liner. Position the cylinder liner in the cylinder bore.
Secure the spacer plate and the cylinder liner in position according to the following procedure:
Install bolts (4) and the washers around the cylinder liner.
Tighten bolts (4) evenly to a torque of 95 N m (70 lb ft).
Install Tooling (B). Ensure that Tooling (B) is in position at the center of the cylinder liner. Ensure that the surface of the cylinder liner is clean. Tighten the bolts on Tooling (B) evenly to a torque of 70 N m (50 lb ft).
Use Tooling (C) to measure the liner projection.
Place the gauge body on the spacer plate near the liner flange. Gauge should read zero. Position the gauge body so that the point is on the outer ring of the liner flange. The gauge will read the liner projection. Measure four equally distant points around the liner flange. Note: If the measurements around the liner are different, rotate the liner to a different position within the bore. If the liner projection is not within specifications, move the liner to a different bore. Inspect the top face of the cylinder block. Measure the cylinder block bore for the liner. If the bore is too shallow, the bore may require rework.
The liner projection must be 0.059 to 0.199 mm (0.0023 to 0.0078 inch). The maximum acceptable difference between the high measurements and the low measurements is 0.05 mm (0.002 inch).
Illustration 2 g00578874
If the liner projection is not 0.059 to 0.199 mm (0.0023 to 0.0078 inch), measure the thickness of the following items: (5) Spacer plate ... 12.31 0.025 mm (0.490 0.0010 inch) (6) Spacer plate gasket ... 0.21 0.025 mm (0.010 0.0010 inch) (7) Cylinder liner flange ... 12.65 0.020 mm (0.500 0.0010 inch)
When the liner projection is correct, make alignment marks on the liner and the cylinder block.
Remove Tooling (B) and Tooling (C). Remove the liner, the spacer plate, and the gasket for the spacer plate. Install the Cylinder Liner
Illustration 3 g01004731
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the cylinder block bore for cylinder liner (2) with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (2).
Immediately install cylinder liner (2) before filler band (3) can expand. Ensure that the marks that are on cylinder liner (2) and the cylinder block are aligned.
Illustration 4 g01256602
Use Tooling (D) to press the cylinder liner into the cylinder block. End By:
Install the pistons and connecting rods.


Parts nipple Volvo Penta:

941438
 
941438 Nipple
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, A
191397
Nipple
191397 Nipple
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, A
954336
 
954336 Nipple
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, A
954337
 
954337 Nipple
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ14
827844
 
827844 Nipple
MD11; MD11C; MD11D, MD1B; MD2B; AQD2B
396033
Nipple
396033 Nipple
MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD40A; TMD40A; TMD40B
396005
Nipple
396005 Nipple
MD11; MD11C; MD11D, MD1B; MD2B; AQD2B
396003
Nipple
396003 Nipple
MD11; MD11C; MD11D, MD1B; MD2B; AQD2B
Back to top