1556448 Nozzle Volvo.Penta
TD164KAE
Nozzle
Price: query
Rating:
Compatible models:
TD164KAE
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
Clean the bottom face of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves in order to identify the correct position.
Illustration 1 g01376164
Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb). Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent damage to the machined face.
Illustration 2 g01376174
Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not compress the spring so that valve spring retainer (4) touches valve stem seal (6).
Slowly release the pressure on Tooling (B).
Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
Use Tooling (C) in order to remove valve stem seal (6).
Repeat Steps 4 through 7 for the remaining valves. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting, "Cylinder Head Inspect".
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves ".
Inspect valve springs (5) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves ".
Illustration 4 g01376184
Illustration 5 g01376926
Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate positi
Parts nozzle Volvo Penta:
1543723
1543723 Nozzle
TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TD164KAE, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G
3825384
3825384 Nozzle, cylinder block
TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TD164KAE, TWD1620G; TWD1630G; TAD1630G