3853733 O-ring Volvo.Penta
5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE
O
Price: query
Rating:
Number on catalog scheme: 45
Compatible models:
Volvo Penta entire parts catalog list:
- Fuel System & Lower Intake Manifold » 3853733
- Fuel System & Lower Intake Manifold
- Fuel System & Lower Intake Manifold
5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE; 5.0FIPNCSCE; 5.0FLPNCA; 5.0FLPNCB; 5.0FLPNCM; 5.0FLPNCS
5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE; 5.8FIPNCSCE; 5.8FLINCC; 5.8FLINCS; 5.8FLPNCA; 5.8FLPNCB; 5.8FLPNCM; 5.8FLPNCS; 5.8FSIINCC; 5.8FSIINC
Information:
Introduction
New engine breathers are now available for the engine valve covers. The new engine breathers are used as a replacement for the former engine breather which is mounted on the rear engine cover housing.Problem
The former 231-9330 Breather Gp is difficult to service in this current location. The new arrangement makes servicing of these components more accessible. Solution
Replace the existing 231-9330 Breather Gp with two 282-9105 Breather As . Refer to the following procedure in order to install the new 282-9105 Breather As .Parts Required
Table 1
Part Number Description Qty
273-8703 Cover 1
227-5538 O-Ring Seal 1
223-1993 Cover 2
224-7506 Valve Cover Seal 2
282-9105 Breather As 2
292-1163 Elbow 2
4W-3034 Hose Clamp 2
033-6031 O-Ring Seal 2
5P-8211 O-Ring Seal 2
126-0559 Bolt 4
322-2820 Tube As 1
8N-6265 Bracket 1
0L-1351 Bolt 1
5M-2894 Hard Washer 1
5P-7470 Clip 1
5P-7471 Clip 1
5P-8245 Hard Washer 2
5P-0597 Hose Clamp 4
6V-1875 Grommet 1
7B-3235 Bolt 1
5B-9604 Hose 2
1F-7958 Full Nut 1
212-7728 Isolator Washer 12 Disassembly Procedure
Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01640813
(1) 304-2812 Tube (2) 5P-0597 Hose Clamp (3) 281-9501 Elbow Hose (4) 5P-4868 Hose Clamp (5) 130-3374 Clip
Remove and discard Item (1) through Item (5).
Illustration 2 g01641835
(6) 231-9330 Breather Gp (7) 227-5538 O-Ring Seal
Remove and discard 231-9330 (6) and 227-5538 O-Ring Seal (7).
Illustration 3 g01640833
Top right side view of engine (8) 238-9850 Covers (9) 7X-0440 Bolts (10) 8T-4224 Hard Washers
Remove and discard two covers (8) from cylinders six and eight and cylinders ten and twelve.Note: Retain 12 bolts (9) and 12 washers (10) for reassembly.Assembly Procedure
Illustration 4 g01641836
(1) 273-8703 Cover (2) 227-5538 O-Ring Seal
Install 273-8703 Cover (1) and 227-5538 O-Ring Seal (2) .
Illustration 5 g01640876
Top right side view of engine (3) 223-1993 Cover (4) 224-7506 Valve Cover Seal (5) 212-7728 Isolator Washer (6) 7X-0440 Bolt (7) 8T-4224 Hard Washer (8) 292-1163 Elbow (9) 5P-8211 O-Ring Seal (10) 126-0559 Bolt (11) 4W-3034 Hose Clamp (12) 282-9105 Breather As (13) 033-6031 O-Ring Seal
Install two 223-1993 Covers (3), two 224-7506 Valve Cover Seals (4) and twelve 212-7728 Isolator Washers (5) using 7X-0440 Bolts (6) and 8T-4224 Hard Washers (7) retained in Step 3 of the disassembly procedure.
Install two 292-1163 Elbows (8), two 5P-8211 O-Ring Seals (9) and four 126-0559 Bolts (10) .
Install two 4W-3034 Hose Clamps (11), two 282-9105 Breather As (12) and two 033-6031 O-Ring Seals (13) .
Illustration 6 g01640897
(14) 5P-0597 Hose Clamp (15) 5B-9604 Hose (16) 322-2820 Tube As (17) 6V-1875 Grommet (18) 5P-7470 Clip (19) 5P-7471 Clip (20) 8N-6265 Bracket (21) 0L-1351 Bolt (22) 5M-2894 Hard Washer (23) 7B-3235 Bolt (24) 1F-7958 Full Nut
New engine breathers are now available for the engine valve covers. The new engine breathers are used as a replacement for the former engine breather which is mounted on the rear engine cover housing.Problem
The former 231-9330 Breather Gp is difficult to service in this current location. The new arrangement makes servicing of these components more accessible. Solution
Replace the existing 231-9330 Breather Gp with two 282-9105 Breather As . Refer to the following procedure in order to install the new 282-9105 Breather As .Parts Required
Table 1
Part Number Description Qty
273-8703 Cover 1
227-5538 O-Ring Seal 1
223-1993 Cover 2
224-7506 Valve Cover Seal 2
282-9105 Breather As 2
292-1163 Elbow 2
4W-3034 Hose Clamp 2
033-6031 O-Ring Seal 2
5P-8211 O-Ring Seal 2
126-0559 Bolt 4
322-2820 Tube As 1
8N-6265 Bracket 1
0L-1351 Bolt 1
5M-2894 Hard Washer 1
5P-7470 Clip 1
5P-7471 Clip 1
5P-8245 Hard Washer 2
5P-0597 Hose Clamp 4
6V-1875 Grommet 1
7B-3235 Bolt 1
5B-9604 Hose 2
1F-7958 Full Nut 1
212-7728 Isolator Washer 12 Disassembly Procedure
Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01640813
(1) 304-2812 Tube (2) 5P-0597 Hose Clamp (3) 281-9501 Elbow Hose (4) 5P-4868 Hose Clamp (5) 130-3374 Clip
Remove and discard Item (1) through Item (5).
Illustration 2 g01641835
(6) 231-9330 Breather Gp (7) 227-5538 O-Ring Seal
Remove and discard 231-9330 (6) and 227-5538 O-Ring Seal (7).
Illustration 3 g01640833
Top right side view of engine (8) 238-9850 Covers (9) 7X-0440 Bolts (10) 8T-4224 Hard Washers
Remove and discard two covers (8) from cylinders six and eight and cylinders ten and twelve.Note: Retain 12 bolts (9) and 12 washers (10) for reassembly.Assembly Procedure
Illustration 4 g01641836
(1) 273-8703 Cover (2) 227-5538 O-Ring Seal
Install 273-8703 Cover (1) and 227-5538 O-Ring Seal (2) .
Illustration 5 g01640876
Top right side view of engine (3) 223-1993 Cover (4) 224-7506 Valve Cover Seal (5) 212-7728 Isolator Washer (6) 7X-0440 Bolt (7) 8T-4224 Hard Washer (8) 292-1163 Elbow (9) 5P-8211 O-Ring Seal (10) 126-0559 Bolt (11) 4W-3034 Hose Clamp (12) 282-9105 Breather As (13) 033-6031 O-Ring Seal
Install two 223-1993 Covers (3), two 224-7506 Valve Cover Seals (4) and twelve 212-7728 Isolator Washers (5) using 7X-0440 Bolts (6) and 8T-4224 Hard Washers (7) retained in Step 3 of the disassembly procedure.
Install two 292-1163 Elbows (8), two 5P-8211 O-Ring Seals (9) and four 126-0559 Bolts (10) .
Install two 4W-3034 Hose Clamps (11), two 282-9105 Breather As (12) and two 033-6031 O-Ring Seals (13) .
Illustration 6 g01640897
(14) 5P-0597 Hose Clamp (15) 5B-9604 Hose (16) 322-2820 Tube As (17) 6V-1875 Grommet (18) 5P-7470 Clip (19) 5P-7471 Clip (20) 8N-6265 Bracket (21) 0L-1351 Bolt (22) 5M-2894 Hard Washer (23) 7B-3235 Bolt (24) 1F-7958 Full Nut
Parts o Volvo Penta:
925064
925064 O-ring
2001; 2001B; 2001AG, 230A; 230B; 250A, 430; 430A; 430B, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE, 7.4GiPEFS; 7.4GSiPEFS;
925256
925256 O-ring
120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR, 2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5
3852033
3852033 O-ring
3.0GLM-C; 3.0GLP-C, 3.0GLMMDA; 3.0GSPMDA, 3.0GLP-A; 3.0GLP-B; 3.0GLM-A, 3.0GLP-D, 3.0GLP-E, 3.0GLP-J; 3.0GLP-N, 3.0GSMBYMCE; 3.0GSPBYCCE, 3.0GSMHUB; 3.0GSPHUB, 3.0GSMLKD; 3.0GSPLKD, 3.0GSMNCA; 3.0GSMNCS; 3.0GSPNCA, 3.0GSMWTR; 3.0GSMWTS; 3.0GSPWTR, 3.
3853674
3853674 O-ring
3.0GLM-C; 3.0GLP-C, 3.0GLMMDA; 3.0GSPMDA, 3.0GLP-A; 3.0GLP-B; 3.0GLM-A, 3.0GLP-D, 3.0GLP-E, 3.0GLP-J; 3.0GLP-N, 3.0GSMBYMCE; 3.0GSPBYCCE, 3.0GSMHUB; 3.0GSPHUB, 3.0GSMLKD; 3.0GSPLKD, 3.0GSMNCA; 3.0GSMNCS; 3.0GSPNCA, 3.0GSMWTR; 3.0GSMWTS; 3.0GSPWTR, 3.
3852071
3852071 O-ring
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 4.3GLPWTC; 4.3GLPWTR; 4.3GSPWTC, 4
3852089
3852089 O-ring
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GL-P, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4
3850820
3850820 O-ring
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GL-P, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4
3850819
3850819 O-ring
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GL-P, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4