960169 Volvo.Penta O-ring

3. Disconnect governor linkage (1) from the governor lever.4. Remove bolt (2) and nut (4). Remove bracket (5). Remove fuel filter outlet line (3) from the filter and fuel injection pump housing. 5. Disconnect fuel supply line (6) from fuel supply line (9). Remove bolt (7) and disconnect fuel supply line (9) from the transfer pump. Remove fuel supply line (9).6. Disconnect fuel filter supply line (8) from the fuel filter and transfer pump. Remove the bolt that holds the clip for fuel filter supply line (8) to the governor housing. Remove fuel filter supply line (8). 7. Remove bracket (10).8. Disconnect oil supply line (11) from the oil manifold. 9. Remove bolts (13) that hold the fuel injection pump housing to the accessory drive. Remove fuel injection pump housing and governor (12) as a unit.10. Remove oil manifold (14).Install Fuel Injection Pump Housing And Governor
1. Make sure O-ring seals (1) are in position on the oil manifold. Put oil on all the O-ring seals on the oil manifold.2. Install oil manifold (2) on the bottom of the fuel injection pump housing.3. Check the timing of the accessory drive shaft. See INSTALL ACCESSORY DRIVE HOUSING.
Make sure the oil manifold sleeve slides into the fitting in the timing gear plate and oil supply tube (4) slides into the fitting on the oil manifold when the fuel injection housing and governor are installed.
4. Install the gasket between the fuel injection housing and the accessory drive housing. Put fuel injection pump housing and governor (3) in position as a unit. Make sure the end of the accessory drive shaft is engaged in the groove (slot) in the fuel injection pump camshaft. 5. Put bracket (6) in position and install the two bolts that hold the bracket. Do not tighten the bolts.6. Install bolts (5) that hold the fuel injection pump housing to the accessory drive. Tighten the two bolts that hold bracket (6) in place.7. Connect oil supply tube (4). 8. Connect fuel supply line (13) to the transfer pump and to fuel supply line (10).9. Connect fuel filter supply line (14) to the transfer pump and to the fuel filter.10. Install the clips that hold the fuel supply line and fuel filter supply line in place.11. Tighten valves (12) for the fuel supply line and the fuel filter supply line to a torque of 18 to 22 lb.ft. (24 to 28 N m).12. Connect governor linkage (11) to the governor lever.13. Install fuel filter outlet line (8) to the fuel injection pump housing and fuel filter.14. Install clips (7) and bracket (9) that hold the outlet line in place.15. Turn the valve on the bottom of the fuel tank to the "ON" position.16. Install the engine side panel on the right side of the machine.end by:a) install fuel injection linesSeparation Of Governor From Fuel Injection Pump Housing
start by:a) remove fuel injection pump housing and governor 1. Remove lever (2) and cover (1) from the governor housing. 2. Remove screw (4) from rack stop collar (3) and remove collar (3). Remove the collar and spring from behind collar (3), if so equipped. 3. Remove bolts (5) that hold the governor housing to the fuel injection pump housing. Remove governor housing (6).4. Remove seat assembly (7) and spring (8). Remove the washer-type spring from the governor bolt and weight assembly. 5. Remove bolts (9) and the lock that hold weight assembly (10) to the fuel injection pump housing.6. Pull weight assembly (10) straight back to remove it from the dowels in the pump housing.7. Move the weight assembly (10) to the side to remove it from rack (11).Connection Of Governor To Fuel Injection Pump Housing
1. Put cylinder and weights (1) on the pump housing with the groove (slot) in the piston over the end of rack (2). 2. Push weight assembly (1) on to the dowels in the pump housing and install lock and bolts (5).3. Install the washer spring, governor spring (6) and seat (4). Install the washer-type spring so the inside diameter of spring will make contact with the guide in governor housing. 4. Put governor housing (3) in position on the pump housing and install bolts (9).5. Install the spring on the end of the governor bolt. Install rack stop collar (7).6. Install rack stop collar screw (8).
TYPICAL EXAMPLE7. Install cover (10) and the gasket on the governor housing. Make sure dowel (11) in cover (10) fits in the opening of rack stop collar (7) before the bolts are tightened.end by:a) install fuel injection pump housing and governor as a unit.b) make an adjustment to rack and governor (See FUEL RACK SETTING AND GOVERNOR ADJUSTMENTS in TESTING AND ADJUSTING)