1523482 Volvo.Penta Oil collector

Illustration 1 g03402526
Cat Alarm and Protection Control Panel
(1) Direct control unit panel (DCU)
(2) "AUX 1 POWER" lamp
(3) "AUX 2 POWER" lamp
(4) "COMMON SHUTDOWN" lamp
(5) "GENERAL ALARM" lamp
(6) "EMERGENCY" switch
(7) "SPEED CONTROL" switch
(8) "GOVERNOR CONTROL" switch
(9) "ENGINE CONTROL" switch
Illustration 2 g03728842
(10) "LOCAL THROTTLE" switch
(11) "CRANK OVERRIDE" switch
(12) "MANUAL RUN/STOP" switch
(13) "LOW IDLE" switch
(14) "ENGINE PRTN OVERRIDE" switch
(15) "PRELUBE OVERRIDE" switch
(16) "MANUAL PRELUBE" switch
Illustration 3 g03409723
DCU Panel
(17) LCD screen
(18) "POWER" indicator lamp
(19) "ALARM" list
(20) "START" switch
(21) "STOP" switch
(22) Context-sensitive menu switches (soft switches)
(23) "SCROLL DOWN" switch
(24) "SCROLL UP" switch
(25) "MENU" switch Cat Marine Power Display (MPD)
Illustration 4 g03579197
(1) Cat Marine Power Display (CMPD)
(2) "ALARM ACKNOWLEDGEMENT"
(3) "SCREEN" display
(4) "ARROW "keys
(5) "AUX 1 POWER" lamp
(6) "AUX 2 POWER" lamp
(7) "SHUTDOWN" lamp
(8) "GENERAL ALARM" lamp
(9) "HORN"
(10) "LOCAL/OFF/REMOTE" switch
(11) " SPEED CONTROL" switch
(12) "LOCAL EMERGENCY STOP" switch
(13) "GOVERNOR CONTROL" switch
(14) "START/STOP" switch Cat Marine Power Display (1) Operating Information
There are three modes of display for the engine data: analog, digital and bar graph. The following parameters are displayed: engine speed, percent load, boost pressure, coolant temperature, oil pressure, oil temperature, fuel rate, fuel pressure, fuel temperature, inlet manifold temperature, transmission temperature, transmission pressure, engine hours and battery voltage.Note: The oil temperature and the inlet manifold temperature will be displayed if the engine is equipped with the appropriate sensors.Display Modes
Day Mode - The normal display is a white background with black letters and gauges. Press and hold down "SCREEN DISPLAY" (3) to display the slide bar that adjusts the contrast. Use the "ARROW" keys (4) to adjust the contrast.Night Mode - Press "SCREEN DISPLAY" (3) to change the display. The display will have a black background with red letters and gauges. Press and hold down "SCREEN DISPLAY" (3) again in order to display the slide bar that adjusts the brightness. Use the "ARROW" keys (4) to adjust the brightness. Press "SCREEN DISPLAY" (3) again in order to display the slide bar that adjusts the contrast while the backlight is on. Use the "ARROW" keys (4) to adjust the contrast. Press "SCREEN DISPLAY" (3) to exit the slide bar that adjusts the contrast.Diagnostic Data
All diagnostic messages from the Electronic Control Module (ECM) of the engine are indicated by both a visual alarm and an audible alarm. Diagnostic indicators will not be shown when there are no active diagnostic codes. The diagnostic indicator will appear in the upper left corner of the screen. A window that describes the diagnostic code will appear in the center of the screen, and the audible alarm will sound. Press the "ALARM ACKNOWLEDGEMENT" (2) key in order to silence the alarm. Press the "ALARM ACKNOWLEDGEMENT" (2) key again to scroll through the diagnostic codes or remove the diagnostic codes. The diagnostic code indicator will remain on the screen until the fault is corrected.Note: The loss of signal to the display will result in a diagnostic code with the description “"NO DATA LINK SIGNAL"”.Configuration and Operation of the Marine Power Display
The Cat Marine Power Display can be programmed for three users with five screens for each user. Three users can set up the Cat Marine Power Display for the preferences of each user.The buttons have multiple functions that are dependent on the screen that is displayed.Reference: See Operator Manual, LEBM0189, "Marine Power Display" for the functions of the buttons."System Information" Screen
When power is first applied, scroll through the screens until the "System Information" screen is shown. This screen allows the following parameters to be configured: "User Name", "Unit Location", "Display Units" and "Vessel Speed". A menu driven screen is located in the upper right corner of the Marine Power Display screen. Press the "ALARM ACKNOWLEDGEMENT" key to display the functions of the buttons.Reference: See Operator Manual, LEBM0189, "Marine Power Display" to configure the parameters.Gauge Screens
The gauge screens can be configured with three different sizes of three types of gauges. Each user can configure the screens to display the engine data according to individual preferences. Each user can configure the screens to display the engine data in the following formats: analog, digital and bar graph.Note: Consult your Cat dealer in order to customize the screens of the Cat Marine Power Display."AUX 1 POWER" Lamp (5)
The lamp will illuminate with a green light when auxiliary power 1 is present."AUX 2 POWER" Lamp (6)
The lamp will illuminate with a green light when auxiliary power 2 is present."SHUTDOWN" Lamp (7)
The lamp will illuminate with a red light when an engine shutdown is active."GENERAL ALARM" Lamp (8)
The lamp will illuminate with an amber light when an alarm is active."HORN" (9)
The alarm will sound in order to alert the operator to an abnormal condition."LOCAL/OFF/REMOTE" Switch (10)
This switch allows the engine to be controlled remotely. This switch also allows the engine to be controlled from a potentiometer on the panel, if equipped. This switch also allows the engine to be shut off."SPEED CONTROL" Switch (11)
This switch is used to control the engine rpm."EMERGENCY STOP" Switch (12)
Use the emergency stop switch ONLY in an emergency situation. DO NOT use the emergency stop switch for normal engine stopping. After an emergency stop, DO NOT start the engine