3581779 Volvo.Penta Oil pipe

Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Turn the battery disconnect switch to the OFF position.
Turn the fuel supply to the OFF position.
Illustration 1 g02524979
Make temporary identification marks on plastic tube assemblies in order to show the correct position of the plastic tube assemblies.
Place a suitable container below the fuel filter base in order to catch any fuel that might be spilled.
Disconnect plastic tube assembly (3) and plastic tube assembly (4) from the assembly of primary fuel filter (1). Use Tooling (A) in order to plug the plastic tube assemblies with new plugs. Use Tooling (A) in order to cap the ports in the primary fuel filter with new caps.
Disconnect the Original Equipment Manufactures (OEM) harness assembly from the connection on harness assembly (5) for water in fuel sensor (6).
Remove bolts (2) and remove the assembly of primary fuel filter (1) from the mounting bracket.
Illustration 2 g02524997
If necessary, follow Step 8.a through Step 8.d in order to disassembly the assembly of primary fuel filter (1).
Remove connection (7) and remove O-ring seal (8). Use Tooling (A) in order to plug the primary fuel filter (1) with new plug. Use Tooling (A) in order to cap connection (7) with new caps.
Remove connection (10) and remove O-ring seal (9). Use Tooling (A) in order to plug the primary fuel filter (1) with new plug. Use Tooling (A) in order to cap connection (10) with new caps.
Remove water in fuel sensor (6) and remove O-ring seal (12).
Remove the filter element from fuel filter canister (11). Refer to Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace" for the correct procedure. Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting , "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the fuel filter base is clean and free from damage. If necessary, replace the complete fuel filter base and filter assembly.
Illustration 3 g02524997
If necessary, follow Step 2.a through Step 2.f in order to assembly primary fuel filter (1).
Install a new filter element to fuel filter canister (11). Refer to Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace" for the correct procedure.
Remove caps from connection (7). Install a new O-ring seal (8) to connection (7).
Remove cap from primary fuel filter (1). Install connection (7) to primary fuel filter (1). Tighten the connection to a torque of 20 N m (177 lb in).
Remove caps from connection (10). Install a new O-ring seal (9) to connection (10).
Remove cap from primary fuel filter (1). Install connection (10) to primary fuel filter (1). Tighten the connection to a torque of 20 N m (177 lb in).
Install a new O-ring seal (12) to water in fuel sensor (6). Install water in fuel sensor (6) to primary fuel filter (1). Tighten water in fuel sensor (6) hand tight.
Illustration 4 g02524979
Position the assembly of primary fuel filter (1) onto the mounting bracket.
Install bolts (2) to the assembly of primary fuel filter (1). Tighten the bolts to a torque of 44 N m (32 lb ft).
Remove the plugs from the plastic tube assemblies. Remove the caps from the connections on the primary fuel filter.
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Serious damage to the engine will result if contaminated fuel enters the fuel system.
Connect plastic tube assembly (3) and plastic tube assembly (4) to primary fuel filter (1).
Connect the OEM harness assembly to the connection on harness assembly (5) for water in fuel sensor (6).
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position. End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.