3827475 Oil drain pump Volvo.Penta
1372, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D5A-T; D5A
Oil
Price: query
Rating:
Compatible models:
1372
D11A-A; D11A-B; D11A-C
D11B1-A MP; D11B2-A MP
D12D-A MG; D12D-E MG
D12D-A MH; D12D-B MH; D12D-C MH
D13B-E MH; D13B-E MH (FE); D13B-N MH
D13B-F MG; D13B-E MG; D13B-E MG (FE)
D16C-A MG
D16C-A MH; D16C-B MH; D16C-C MH
D16C-D MH
D5A-T; D5A-TA; D5A-B TA
D9A2A; D9A2A D9-425; D9A2A D9-500
D9A2A; D9A2A MG; D9A2A D9A-MG
TAD1140VE; TAD1141VE; TAD1142VE
TAD1150VE; TAD1151VE; TAD1152VE
TAD1170VE; TAD1171VE; TAD1172VE
TAD1240GE; TAD1241GE; TAD1242GE
TAD1340VE; TAD1341VE; TAD1342VE
TAD1341GE; TAD1342GE; TAD1343GE
TAD1350VE
TAD1351VE; TAD1352VE; TAD1353VE
TAD1352VE
TAD1360VE
TAD1361VE
TAD1363VE
TAD1371VE; TAD1372VE; TAD1373VE
TAD1640GE; TAD1641GE; TAD1642GE
TAD1641VE; TAD1642VE; TAD1643VE
TAD1643VE-B
TAD1650VE-B; TAD1650VE-B/51VE; TAD1651VE
TAD1670VE; TAD1671VE; TAD1672VE
TAD520GE; TAD720GE; TAD721GE
TAD540-42VE; TAD550-51VE; TAD540VE
TAD550GE; TAD551GE; TAD750GE
TAD560VE; TAD561VE; TAD761VE
TAD570VE; TAD571VE; TAD572VE
TAD650VE; TAD660VE
TAD734GE
TAD750VE; TAD760VE
TAD840VE; TAD841VE; TAD842VE
TAD870VE; TAD871VE; TAD872VE
TAD940GE; TAD941GE
TAD940VE; TAD941VE; TAD942VE
TAMD74A; TAMD74A-A; TAMD74A-B
TD520GE; TAD530GE; TAD531GE
TD520VE; TD720VE
TD610G; TWD610G; TD710G
TWD1240VE; TAD1241VE; TAD1242VE
TWD1672GE; TWD1673GE; TWD1672-1673GE
Volvo.Penta
Volvo Penta entire parts catalog list:
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump » 3827475
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
D12D-A MH; D12D-B MH; D12D-C MH; D12D-E MH; D12D-G MH; D12C-A MP; D12D-A MP; D12D-B MP; D12D-C MP; D12D-D MP; D12D-E MP; D12D-F MP; D12D-G M
D13B-E MH; D13B-E MH (FE); D13B-N MH; D13B-N MH (FE)
D13B-F MG; D13B-E MG; D13B-E MG (FE); D13B-F MG (FE)
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
D16C-A MH; D16C-B MH; D16C-C MH
D16C-D MH
D5A-T; D5A-TA; D5A-B TA; D7A-T; D7A-TA; D7A-B TA
D5A-T; D5A-TA; D5A-B TA; D7A-T; D7A-TA; D7A-B TA; D7C-TA; D7C-B TA
- Oil Drain Pump, Enginemounted (0-5°)
- Oil Drain Pump, Enginemounted (0-5°)
- Oil Drain Pump, Enginemounted (0-10°)
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
TAD1340VE; TAD1341VE; TAD1342VE; TAD1343VE; TAD1344VE; TAD1345VE; TAD1360VE; TAD1361VE; TAD1362VE; TAD1363VE; TAD1364VE; TAD1365VE; TAD1360-
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
TAD1350VE
TAD1351VE; TAD1352VE; TAD1353VE; TAD1351-53VE
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Aluminum Sump
- Oil Drain Pump and Installation Parts, Engine Mounted for Plastic Sump
TAD1641VE; TAD1642VE; TAD1643VE; TAD1650VE; TAD1660VE; TAD1661VE; TAD1662VE; TAD1640VE-B; TAD1641VE-B; TAD1642VE-B; TAD1660-62VE; TAD1662VE
- Oil Drain Pump and Installation Parts. For aluminium sump
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts. For aluminium sump
- Oil Drain Pump and Installation Parts. For plastic sump
- Oil Drain Pump and Installation Parts. For plastic sump
- Oil Drain Pump and Installation Parts. For aluminium sump
- Oil Drain Pump and Installation Parts. For aluminium sump
- Oil Drain Pump and Installation Parts. For plastic sump
TAD540-42VE; TAD550-51VE; TAD540VE; TAD541VE; TAD542VE; TAD550VE; TAD551VE; TAD552VE
TAD550GE; TAD551GE; TAD750GE; TAD751GE; TAD752GE; TAD753GE; TAD754GE
- Oil Drain Pump and Installation Parts, Engine Mounted
- Oil Drain Pump and Installation Parts, Engine Mounted
TAD570VE; TAD571VE; TAD572VE
TAD650VE; TAD660VE
TAD734GE
- Oil Drain Pump and Installation Parts, Engine Mounted SN-11560446
- Oil Drain Pump and Installation Parts, Engine Mounted SN11560447-
TAD840VE; TAD841VE; TAD842VE; TAD843VE; TAD852VE; TAD851VE; TAD853VE; TAD850-52VE; TAD840-43VE
TAD870VE; TAD871VE; TAD872VE; TAD873VE
TAD940GE; TAD941GE
TAD940VE; TAD941VE; TAD942VE; TAD943VE; TAD950VE; TAD951VE; TAD952VE
TAMD74A; TAMD74A-A; TAMD74A-B; TAMD74C-A; TAMD74C-B; TAMD74L-A; TAMD74L-B; TAMD74P-A; TAMD74P-B; TAMD75P-A
TD520GE; TAD530GE; TAD531GE; TAD532GE; TD720GE; TAD720GE; TAD730GE; TAD731GE; TAD732GE; TAD733GE; TAD530GE MECH; TAD530GE EDC4; TAD531GE MEC
- Oil Bilge Pump
- Oil Bilge Pump, Motor Specification Number: 869335, 869336, 869337, 869338
- Oil Bilge Pump
TD610G; TWD610G; TD710G; TWD710G; TAD730G; TWD740GE; TAD740GE; TAD741GE
TWD1240VE; TAD1241VE; TAD1242VE; TAD1250VE; TAD1251VE; TAD1252VE
TWD1672GE; TWD1673GE; TWD1672-1673GE
Information:
Start By:a. remove timing gear coverb. remove electric starting motor 1. Time the engine as follows:a. Install Tool (A) in the flywheel housingb. Remove the cover from the side of the fuel injection pump housing so Tool (B) can be installed. Remove the plug from the flywheel housing so bolt (1) can be installed. The engine is seen from the flywheel end when the direction of rotation is given. c. Turn the flywheel counterclockwise until Tool (B) can be installed in the fuel injection pump housing and located in the groove in the fuel injection pump camshaft, a 3/8 in-16 NC × 2.25 in long bolt (1) can be installed in the flywheel through the hole in the flywheel housing, and the "C" marks on the crankshaft gear and the camshaft gear are in alignment with each other. 2. Loosen bolt (2) until there is approximately 3.18 mm (.125 in) gap between washer (3) and fuel pump drive gear (4).3. Install Tooling (C) as shown, and loosen the fuel pump drive gear from the taper on the fuel injection pump camshaft. Remove Tooling (C), the bolt, washer and fuel pump drive gear.4. Remove the bolts and plate (5) that hold idler gear (6) in position. Remove the idler gear. If necessary, remove the bearing from the idler gear with Tooling (D) and a press.
Do not turn the crankshaft after camshaft gear (7) has been removed. Turning the crankshaft will cause damage to the valves.
5. Remove the four bolts that hold camshaft gear (7) to the camshaft. Remove the camshaft gear.6. Remove the three nuts on the back side of timing gear plate (8) that hold the fuel pump housing to timing gear plate (8). 7. Bend locks (9) away from the bolts.8. Remove the bolts, locks (9), and timing gear plate (8) from the cylinder block.9. Remove the old gasket material from the cylinder block and timing gear plate (8).Install Timing Gears & Plate
1. Make sure O-ring seal (10) is in place on the fuel pump housing.2. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block. Put 5H-2471 Gasket Cement on the bottom of the gasket where the gasket makes contact with the gasket for the oil pan. 3. Put timing gear plate (8) in position on the cylinder block. Install the three nuts that hold the fuel pump housing onto the back side of timing gear plate (8). Install locks (9) and the six bolts that hold timing gear plate (8) in place. Bend locks (9) against the bolts. 4. Install camshaft gear (7) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear. Install the washers and bolts (11) that hold camshaft gear (7) to the camshaft.5. Install the bearing in idler gear (6) with Tooling (D) and a press. The end of the bearing must be 1.52 mm (.060 in) below the face of the gear hub. 6. Be sure the oil hole in the shaft for idler gear (6) is open. Put idler gear (6) in position. Install plate (5) and bolts (12). 7. Make sure Tooling (B) is in position in the groove of the fuel injection pump camshaft. 8. Put fuel injection pump drive gear (4) in position on the fuel injection pump camshaft. Put washer (3) in position on the gear with the largest diameter toward the front of the engine. Install bolt (2), and tighten it to a torque of 7 N m (5 lb ft). Make sure bolt (2) does not turn while the flywheel is being turned. The engine is seen from the flywheel end when the direction of rotation is given. 9. Remove bolt (1) from the flywheel. Use Tool (A) to turn the flywheel clockwise until the "C" mark on the crankshaft gear moves 30 degrees.10. Turn the flywheel counterclockwise until the 3/8 in-16 NC × 57.1 mm (2.25 in) bolt (1) can be installed in the flywheel and the "C" marks are in alignment. This will remove all the backlash from the timing gears.11. Install a 3/81/2 in-24 NF × 12.7 mm ( in) long bolt in one of the holes in fuel injection pump drive gear (4).12. Put a torque wrench on the 3/8 in bolt with the wrench in line with the center of the drive gear, and give it a torque of 60 to 70 N m (45 to 50 lb ft). While this torque is held, tighten the drive gear bolt to a torque of 270 25 N m (200 18 lb ft).13. Remove Tool (B) from the fuel injection pump housing and install the cover.14. Remove bolt (1) from the flywheel and install the plug in the flywheel housing.15. Remove Tool (A) from the flywheel housing.End By:a. install timing gear coverb. install electric starting motor
Do not turn the crankshaft after camshaft gear (7) has been removed. Turning the crankshaft will cause damage to the valves.
5. Remove the four bolts that hold camshaft gear (7) to the camshaft. Remove the camshaft gear.6. Remove the three nuts on the back side of timing gear plate (8) that hold the fuel pump housing to timing gear plate (8). 7. Bend locks (9) away from the bolts.8. Remove the bolts, locks (9), and timing gear plate (8) from the cylinder block.9. Remove the old gasket material from the cylinder block and timing gear plate (8).Install Timing Gears & Plate
1. Make sure O-ring seal (10) is in place on the fuel pump housing.2. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block. Put 5H-2471 Gasket Cement on the bottom of the gasket where the gasket makes contact with the gasket for the oil pan. 3. Put timing gear plate (8) in position on the cylinder block. Install the three nuts that hold the fuel pump housing onto the back side of timing gear plate (8). Install locks (9) and the six bolts that hold timing gear plate (8) in place. Bend locks (9) against the bolts. 4. Install camshaft gear (7) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear. Install the washers and bolts (11) that hold camshaft gear (7) to the camshaft.5. Install the bearing in idler gear (6) with Tooling (D) and a press. The end of the bearing must be 1.52 mm (.060 in) below the face of the gear hub. 6. Be sure the oil hole in the shaft for idler gear (6) is open. Put idler gear (6) in position. Install plate (5) and bolts (12). 7. Make sure Tooling (B) is in position in the groove of the fuel injection pump camshaft. 8. Put fuel injection pump drive gear (4) in position on the fuel injection pump camshaft. Put washer (3) in position on the gear with the largest diameter toward the front of the engine. Install bolt (2), and tighten it to a torque of 7 N m (5 lb ft). Make sure bolt (2) does not turn while the flywheel is being turned. The engine is seen from the flywheel end when the direction of rotation is given. 9. Remove bolt (1) from the flywheel. Use Tool (A) to turn the flywheel clockwise until the "C" mark on the crankshaft gear moves 30 degrees.10. Turn the flywheel counterclockwise until the 3/8 in-16 NC × 57.1 mm (2.25 in) bolt (1) can be installed in the flywheel and the "C" marks are in alignment. This will remove all the backlash from the timing gears.11. Install a 3/81/2 in-24 NF × 12.7 mm ( in) long bolt in one of the holes in fuel injection pump drive gear (4).12. Put a torque wrench on the 3/8 in bolt with the wrench in line with the center of the drive gear, and give it a torque of 60 to 70 N m (45 to 50 lb ft). While this torque is held, tighten the drive gear bolt to a torque of 270 25 N m (200 18 lb ft).13. Remove Tool (B) from the fuel injection pump housing and install the cover.14. Remove bolt (1) from the flywheel and install the plug in the flywheel housing.15. Remove Tool (A) from the flywheel housing.End By:a. install timing gear coverb. install electric starting motor
Parts oil Volvo Penta:
477556
477556 Oil filter
D11A-A; D11A-B; D11A-C, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13B-J MP; D13B-M MP, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C
478736
478736 Oil filter
D11A-A; D11A-B; D11A-C, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13B-J MP; D13B-M MP, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C
21707132
21707132 Oil filter
D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, TAD1340VE; TAD1341VE; TAD1342VE, TAD1352VE, TAD16
21707133
21707133 Oil filter
D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, TAD1340VE; TAD1341VE; TAD1342VE, TAD1352VE, TAD16
21042447
21042447 Oil level sensor
D13B-A MP; D13B-B MP; D13B-C MP, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, TAD1340VE; TAD1341VE; TAD1342VE, TAD1341GE; TAD1342GE; TAD1343GE, TAD1350VE, TAD1360VE,
22022794
22022794 Oil level sensor
1372, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-A MG, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1140VE;
420867
420867 Oil pump
TAMD61A; TAMD62A, TD610G; TWD610G; TD710G, TD610M; TD630ME; TWD630ME, TD610V; TWD610V; TD630VE, TD61A; TD61AW; TD61ACE, TWD610P; TWD610PB; TWD710P
20574451