421051 Volvo.Penta Oil pipe


421051 Oil pipe Volvo.Penta D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C Oil
421051 Oil pipe Volvo Penta
Rating:
13

Buy Oil pipe 421051 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$27.46

02-12-2024
0.1102[0.05] pounds
CN: zhengzhousanggushang
Ball Joint Kit For Polaris RZR XP 4 1000 RZR XP 1000 2014-2018; 42-1051 Replace parts
FRELDCVB Selection of , safe and reliable to use, durable || Installation and replacement method is simple. Wonderful replacement for the old or broken one, directly fitment. || Manufacturing ensuring maximum durability, not easy to damage, with good performance and long service life. || Every product has inspection before leaving the factory. || Pictures are taken by the real product.
$33.67

02-12-2024
0.1102[0.05] Pounds
CN: anyangliangzuoshangm
Ball Joint Kit For RZR XP 4 1000 RZR XP 1000 2014-2018; 42-1051 Replacement Parts
WgxzXyl Compatible: Suitable for RZR XP 4 1000 and RZR XP 1000 design, ensure matching. || Material: Adopt wear-resistant and corrosion-resistant materials to enhance durability and long-term performance. || Improve handling: Optimized design improves suspension system performance, improves driving experience and stability. || Simple installation: Easy to install, reduce maintenance time, no complicated tools required. || High reliability: Ensure stable operation under various conditions.
$54.99

02-12-2024

US: AM Autoparts
Rear Left Power Window Regulator & Motor Assembly Drivers Side Compatible with 2005-2010 Chevrolet Cobalt 2003-2007 Saturn Ion
AM Autoparts 10 Year Warranty || Reference Number(s): 11A611,13501956L,15906995,22714604,22738688,421051,748514,821051ar,82304,RPAGM049,WLA2073 || Operation: Power
Number on catalog scheme: 4
 

Information:

Probable Causes
Diagnostic codes
Electrical connectors
ECM connection
Intake manifold pressure
Fuel supplyRecommended Actions
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the Product Status Report (PSR) with Histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is needed.
C. Use the electronic service tool to check for active or logged codes.
Diagnostic codes
Result: There are active or logged codes.
Repair: Troubleshoot any codes before continuing with this procedure.
Result: There are no active or logged codes.
Proceed to Test Step 2.
2. Electrical Connectors
A. Check all electrical connectors for damage. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Make sure that all the connector seals are in place and that the connectors have been correctly installed.
Electrical connectors
Result: An electrical connector is damaged.
Repair: Repair the electrical connector or replace the electrical connector.
Result: A connector seal is displaced or missing or an electrical connector is not correctly installed.
Repair: Repair the electrical connector or replace the electrical connector.
Result: All electrical connectors are OK.
Proceed to Test Step 3.
3. ECM Connection
A. Check that the P2/J2 and P1/J1 connectors are correctly installed.
Note: If a fault is suspected with the ECM power or ground connections, refer to Troubleshooting, "Electrical Power Supply - Test".
ECM connection
Result: An ECM connector is not correctly installed.
Repair: Repair the electrical connector or replace the electrical connector.
Result: Both ECM connectors are correctly installed.
Proceed to Test Step 4.
4. Intake Manifold Pressure
A. Use the electronic service tool to verify the intake manifold pressure.
Turn the start switch to the ON position.
The intake manifold pressure must read 0 0.5 kPa (0 0.07 psi).
Intake manifold
Result: The intake manifold pressure does not read 0 0.5 kPa (0 0.07 psi).
Repair: Refer to Troubleshooting, "Intake Manifold Air Pressure Is Low".
Result: The intake manifold pressure reads 0 0.5 kPa (0 0.07 psi).
Proceed to Test Step 5.
5. Fuel Supply
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
E. Check the primary filter/water separator for water in the fuel.
F. Check for fuel supply lines that are restricted.
G. Check that the low-pressure fuel lines are tight and secured properly.
H. Check that the Electric Priming Pump (EPP) is operating correctly.
I. Replace any filters and/or screens in the fuel system. Refer to Operation and Maintenance Manual for further information.
J. Check the diesel fuel for contamination. Refer to Systems Operation, Testing and Adjusting, "Fuel Quality - Test".
K. Check for air in the fuel system. Refer to Systems Operation, Testing and Adjusting, "Air in Fuel - Test".
L. Ensure that the fuel system has been primed. Refer to Systems Operation, Testing and Adjusting, "Fuel System - Prime".
Fuel system
Result: The fuel supply is not OK.
Repair: Repair the fuel system or replace the fuel system components, as necessary.
Result: The fuel supply is OK.
Proceed to Test Step 6.


Parts oil Volvo Penta:

471034
Oil filter
471034 Oil filter
AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, IPS15-A, IPS2-A, IPS2-B, IPS2-C, IPS3-A, IPS3-C, KAD32P; TAMD42WJ-A; KAD43P-A, MD40A; TMD40A; TMD40B, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD30A; TD31ACE; TD40A, TMD
420172
Oil deflector
420172 Oil deflector
AQD70D; TAMD70D; TAMD70E, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP
832385
 
832385 Oil filter
AQD70D; TAMD70D; TAMD70E, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
466387
Oil pump
466387 Oil pump
D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83
7743240_029
7743240_067
843019
 
843019 Oil bilge pipe
MD70C; TMD70C; TAMD70C
Back to top