862061 Volvo.Penta Oil filler pipe

3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. Keep each cap with the respective connecting rod.4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2).
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not damage the cooling tubes when the pistons are removed.
Install Pistons
1. Put clean engine oil on the piston rings, connecting rod bearings and cylinder liners. 2. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (1) with tool (A).
Be sure the pistons are installed with flat surfaces (2) of the connecting rods toward each other and the chamfered sides (4) toward the crankshaft.
For more detail about installation of connecting rod bearings, see remove and install connecting rod bearings.
Do not use an impact wrench to tighten the nuts the additional 120° when the bearing clearance is being checked.
3. Check the bearing clearance with Plastigage (B).4. Put clean engine oil on bolts (5). Install caps (3) and the nuts finger tight. Tighten each nut to a torque of 80 8 N m (60 6 lb.ft.). Put a mark across the nuts and bolts and tighten each nut 120° more.5. Check the side clearance between two connecting rods on the same crankshaft journal. The clearance must be 0.28 to 0.84 mm (.011 to .033 in.) for new rods.END BY:a. install oil pumpb. install cylinder head assembliesDisassemble And Assemble Pistons
START BY:a. remove pistons 1. Remove bearing halves (2) from the connecting rod and connecting rod cap.2. Use tool (C) to remove retainer rings (1) from each side of the piston. Remove pin (3) and the connecting rod from the piston. 3. Use tool (A) to remove the piston rings from piston (4). 4. Heat the connecting rod to a temperature of 177° - 260°C (350° - 500°F). Put 5P8651 Spacer (12) in the base plate. Put connecting rod in position on the base plate of tooling (B).5. Put the connecting rod piston pin bearing end in the center of the port assembly of tooling (B). Install pin (8) in the center of the bore for the connecting rod bearings.6. Install 5P8650 Adapter (10). Put the hole in the adapter in alignment with the hole in the base plate of tooling (B).7. Install clamp bar (11) and clamp pin (7).8. Install new piston pin bearing (6) on adapter (10). The old bearing is pushed out by tooling (B) as the new bearing is installed.9. Put 5P8649 Adapter (9) in position as shown with the taper side down. The piston pin bearing joint must be in alignment with the hole in adapter (10) and the base plate of tooling (B).10. Put pusher (5) on adapter (9).11. Use tooling (B) to push the new piston pin bearing into the connecting rod until adapter (9) of tooling (B) makes full contact with the connecting rod surface.12. Remove the connecting rod and the old piston pin bearing from tooling (B).13. Check the piston pin bearing bore diameter after the bearing is installed. The correct dimension is 50.830 0.008 mm (2.0012 .0003 in.). 14. Clean the ring grooves in the piston before the rings are installed. The two compression rings have marks "UP-1", "UP-2". The rings must be installed with these marks toward the top of the piston with "UP-1" as the top ring. After installation of all three piston rings, put piston rings in position so the gaps in the rings are 120° apart.15. Use tool (A) to install the piston rings on the piston. 16. Install bearings (2) in the connecting rod and connecting rod cap. Be sure the tabs in back of the bearings are in the tab grooves of the connecting rod and connecting rod cap.17. Put piston (4) in position on the connecting rod. Put clean engine oil on piston pin (3) and install the piston pin. Install retainer rings (1). Make sure the retainer rings are in the grooves of the piston.END BY:a. install pistons