866067 Volvo.Penta Oil pressure pipe


866067 Oil pressure pipe Volvo.Penta TMD102A; TAMD102A; TAMD102D Oil
866067 Oil pressure pipe Volvo Penta
Rating:
28

Buy Oil pressure pipe 866067 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.00
 

30-08-2017

KOCH: KOCH
KOCH 866067 LABEL ROLLER SPACERNEW NO BOX
Factory surplus item
 

30-08-2017

Powers Fas: Powers Fastening Inn
Powers #14 X 2 A FlatPhilTapScr SS (100 Each) 866067
Number on catalog scheme: 9
 

Compatible models:

Volvo Penta entire parts catalog list:

TMD102A; TAMD102A; TAMD102D

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 439-3941 Link Bracket As 2
C - Bel-Ray Molylube 301082(1) -
D 8T-5096 Dial Indicator Gp 1
(1) Refer to the following link to order molylube specified above - www.belray.com.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01049072
If crankshaft gear (7) was removed, install the gear on crankshaft (5).
Check the clearance of the main bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Illustration 2 g01049073Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block. Coat the bearings with clean engine oil.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies. Coat the bearings with clean engine oil.
Illustration 3 g00930694Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach Tooling (B) and a suitable lifting device to crankshaft (5). For 3508 Engines, the crankshaft weighs approximately 398 kg (877 lb). For 3512 Engines, the crankshaft weighs approximately 590 kg (1300 lb). For 3516 Engines, the crankshaft weighs approximately 800 kg (1764 lb). Position the crankshaft in the cylinder block.
Ensure that the lower halves of the main bearings are in position in the main bearing caps. Coat the bearings with clean engine oil.Note: Main bearing caps (4) must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Illustration 4 g03887353
Coat the threads of the bolts for the main bearing caps with clean SAE 30 engine oil. Except for the center main bearing cap, place the main bearing caps into position. Install the bolts and washers.Tighten the bolts according to the sequence that is shown in Illustration Arrow (X) points to the front of the engine. Tighten the bolts to a torque of 190 14 N m (140 10 lb ft). Then tighten the bolts for an extra 180 5 degrees (1/2 turn).
Illustration 5 g01049103
Place clean engine oil on thrust plates (3). Install thrust plates (3).
Install the center main bearing. Use the tightening procedure that is in Step 7.
Use Tooling (D) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Make sure that the upper halves of the bearings are in position on the connecting rods. Make sure that the lower halves of the bearings are in position on the connecting rod caps.
Check the clearance of the connecting rod bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Position one connecting rod onto a journal of the crankshaft.Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 6 g01049104
Illustration 7 g06120079
Place Tooling (C) on the bolt threads, shanks, and seats.
Place connecting rod cap (2) into position. Install the bolts. Use the following procedure to tighten the bolts:
Tighten Bolts (X1) and (X3) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (X2) and (X4) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (X2) and (X4) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an extra 90 5 degrees (1/4 turn). An impact wrench may be used.
After measuring the clearance of the connecting rod bearing, coat the bearings with clean engine oil. Use the same procedure to install the remaining connecting rod caps.
Each counterweight i


Parts oil Volvo Penta:

6631726
 
6631726 Oil pump housing
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TD100G; TD100G-85; TD100G-87, TID120FPP; TID120FG; TD120G, TMD100C,
478736
Oil filter
478736 Oil filter
D11A-A; D11A-B; D11A-C, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13B-J MP; D13B-M MP, D16C-A MG, D16C-A MH; D16C-B MH; D16C-C
479317
Oil pump
479317 Oil pump
TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAMD103A, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TMD102A; TAMD102A; TAMD102D
821792
 
821792 Oil filler pipe, oil filling
D100A; D100AK; D100B, D70B; D70B PP; D70B K, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TD70G; TD70G-83; TD70GPP, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
847741
Oil filter
847741 Oil filter
D5A-T; D5A-TA; D5A-B TA, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD61A; TAMD62A, TAMD63L-A; TAMD63P-A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD72P-A; TAMD72WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TMD102A; TAMD102A; TAMD102D, TMD121C; TA
864391
 
864391 Oil return pipe, oil drain
TAMD103A, TMD102A; TAMD102A; TAMD102D
3826144
 
3826144 Oil cooler
TAMD122A; TMD122A; TAMD122P-A, TMD102A; TAMD102A; TAMD102D
479319
Oil pump
479319 Oil pump
TAD1030G; TD1010G; TWD1010G, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TMD100C, TMD102A; TAMD102A; TAMD102D
Back to top