897823 Volvo.Penta Oil pipe

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
Release the pressure in the cooling system by slowly loosening the filler cap on the radiator.
Drain the coolant from the radiator in a suitable container. The capacity of the cooling system is 37 10 L (10 3 US gal).
Remove the guard assembly from the left side of the engine and the lower access panel from the machine.
Illustration 1 g00730703
Remove plug (7) and drain the coolant from the transmission oil cooler (4). Install plug (7) .
Remove bolts (2) and bolts (5). Disconnect tube assemblies (3) and (8) from the transmission oil cooler (4). Put caps in the tube assemblies in order to prevent the loss of transmission oil.
Remove the nut, two washers and bolt (6) that holds transmission oil cooler (4) to the bracket.
Attach a hoist and attach a suitable lifting device to transmission oil cooler (4). Remove bolts (1) and transmission oil cooler (4). The weight of the transmission oil cooler is 19 42 kg (42 93 lb).
Illustration 2 g00730705
Remove the three remaining bolts (10), nuts (9) and bonnet (11) from the transmission oil cooler.
Illustration 3 g00730706
Clean the tubes of the transmission oil cooler with a rod (12) that has a diameter of 4.78 .188 mm (.1882 .0074 inch).Installation Procedure
All the gasket surfaces should be clean.
Illustration 4 g00730705
Put the gasket and bonnet (11) in position on the transmission oil cooler, and install bolts (10) and nuts (9) .
Illustration 5 g00730703
Use a suitable lifting device. Position the gasket and position transmission oil cooler (4) on the engine. Install bolts (1) in order to secure transmission oil cooler (4) .
Position the O-ring seals. Connect tube assemblies (3) to the transmission oil cooler (4). Connect tube assemblies (8) to transmission oil cooler (4). Install bolts (2) and (5) that secure the tube assemblies.
Install the two washers. Install the nut. Install bolt (6) that secures the transmission oil cooler (4) to the bracket.
Install the guard assembly and the lower access panel on the left side of the engine.
Fill the cooling system to the correct level.Note: Refer to Operation and Maintenance Manual, SEBU7001, "Cooling System" for the correct filling procedure.