844194 Volvo.Penta Pin

Table 1
Diagnostic Codes Table
CDL Code and Description Comments
94–3
Fuel Delivery Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
94–4
Fuel Delivery Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
100-3
Engine Oil Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
100-4
Engine Oil Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
101-3
Crankcase Air Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
101-4
Crankcase Air Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
274-3
Atmospheric Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
274-4
Atmospheric Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
460-3
Fuel Pressure Sensor - After Fuel Filter : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
460-4
Fuel Pressure Sensor - After Fuel Filter : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1785-3
Intake Manifold Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1785-4
Intake Manifold Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1835-3
Auxiliary Pressure Sensor : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1835-4
Auxiliary Pressure Sensor : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
The value of the parameter is set to a gauge pressure.
1924-3
Engine Intake Valve Actuation System Oil Pressure : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range. The code is logged. The value of the parameter is set to a gauge pressure.
1924-4
Engine Intake Valve Actuation System Oil Pressure : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range. The code is logged. The value of the parameter is set to a gauge pressure.
Illustration 1 g06164330Probable Causes
Codes
Short circuit
Open circuit
Supply voltage
Wiring
DPF components
Electrical connectorsRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Establish communication between Cat® Electronic Technician (ET) and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Turn the keyswitch to ON.
C. Look for "-3", or "-4" active or logged codes.
Codes
Result: A -3 diagnostic code is active.
Proceed to Test Step 2.
Result: A -4 diagnostic code is active.
Proceed to Test Step 3.
2. Create a Short at the Sensor Connector
A. Use a test lamp to create a short between terminal 3 (signal) and terminal 2 (sensor return) at the sensor connector.
B. Turn the keyswitch to ON.
C. Monitor the diagnostic codes on Cat ET. Check for an active -4 diagnostic code for the suspect sensor.
D. Turn the keyswitch to OFF.
Short circuit
Result: A -4 diagnostic code does not become active for the suspect sensor.
Proceed to Test Step 4.
Result: A -4 diagnostic code became active after creating the short at the sensor connector. The wiring is OK.
Repair: Replace the sensor.
If the problem is not resolved, proceed to Test Step 3.
3. Create an Open at the Suspect Sensor Connector
A. Turn the keyswitch to OFF.
B. Disconnect the sensor connector of the suspect sensor with the active -4 diagnostic code.
C. Turn the keyswitch to ON.
D. Monitor the diagnostic codes on Cat ET. Check for an active -3 diagnostic code for the suspect sensor.
E. Turn the keyswitch to OFF.
Open circuit
Result: A -3 diagnostic code did not become active after disconnecting the sensor.
Proceed to Test Step 4.
Result: A -3 diagnostic code became active after disconnecting the sensor. The wiring is OK.
Repair: Replace the sensor.
If the problem is not resolved, proceed to Test Step 4.
4. Check the 5 VDC Supply Voltage at the Sensor Connector
A. Turn the keyswitch to ON.
B. Measure the voltage between pin 1 and pin 2 at the suspect sensor.
5.0 0.2 VDC
Result: The supply voltage is OK.
Repair: Connect the sensor.
Proceed to Test Step 5
Result: The supply voltage is NOT OK. There is a short in the harness to the battery.
Repair: Repair the wiring