22702115 Volvo.Penta Pipe


22702115 Pipe Volvo.Penta TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE Pipe
22702115 Pipe Volvo Penta
Rating:
48

Buy Pipe 22702115 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Volvo Penta entire parts catalog list:

TAD840VE; TAD841VE; TAD842VE; TAD843VE; TAD852VE; TAD851VE; TAD853VE; TAD850-52VE; TAD840-43VE
TAD870VE; TAD871VE; TAD872VE; TAD873VE

Information:

1. Drain the coolant from the engine.2. Loosen clamp nut (5).3. Remove hose (6).4. Remove two bolts (3).5. Remove elbow (4).6. Loosen clamp (1).7. Remove hose (2). 8. Remove two clamp bolts (8) on fumes disposal tube (7). 9. Remove clamp bolt (13). Clamp bolt is hidden behind belt tightener pulley.10. Remove two bolts (9).11. Reposition supply elbow (10).12. Loosen hose clamp (11). Disconnect hose (12). 13. Loosen hose clamp (17). Disconnect hose (21).14. Loosen hose clamp (23). Disconnect hose (24).15. Disconnect two hose fittings (19).16. Remove two bolts (20). Remove oil cooler bonnet (22).17. Remove four bolts (16). Remove water pump cover (15).18. Remove seven long bolts (14).19. Remove water pump (18). Check seals and O-rings for wear and damage before installation, replace as necessary. For installation of the water pump, reverse the removal steps.20. Fill radiator with coolant to correct level.End By:a. install fuel tankDisassemble Water Pump
Start By:a. remove water pump The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing.1. Remove O-ring seal (1) from the adapter.2. Remove adapter (2) from the housing. Remove the O-ring seal from the outside diameter of the adapter.3. Remove bolt (3) and the retainer that hold the impeller on the shaft. 4. Use tooling (A) to remove impeller (4) from the shaft. 5. Remove the spring and seal (5) from the shaft. 6. Remove four bolts (7) from retainer (6) that hold the shaft assembly to the pump housing.7. Remove O-ring seal (8) from the housing. 8. Remove gear and shaft assembly (10) from the housing.9. Remove bolt (9) and the retainer from the shaft assembly. 10. Use a press to remove the shaft assembly from gear (11). Remove the retainer from the shaft assembly. 11. Remove bearing (13), spacer (14) and bearing (12) from the shaft. 12. Remove lip-type seal (15) from the housing.13. Turn the housing over, and remove ceramic ring (16) and the seal.Assemble Water Pump
1. Use 6V1541 Quick Cure Primer to clean shaft (8) and the seal counterbore in the pump housing.2. Install bearing (4), spacer (3) and bearing (2) on shaft (8).3. Put retainer (1) and gear (7) in position on the shaft assembly. Install retainer (6) and bolt (5). 4. Use tooling (A) to install the lip seal in the housing as shown. Put a small amount of clean SAE 30 Oil on the lip of the seal. 5. Install a new O-ring seal (10) on the housing.6. Put shaft assembly (9) in position in the housing. Install the bolts that hold the retainer to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put ceramic ring (12) in position in rubber seal (11). Use hand pressure and tool (B) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.8. Remove the spring from seal assembly (13). Use hand pressure and tool (B) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 9. Install spring (15) on the shaft.10. Put impeller (14) in position on the shaft. Install the washer and bolt that holds it. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft). 11. Install O-ring seal (17) on the outside diameter of the adapter. Put a small amount of clean SAE 30 Oil on the O-ring seal.12. Install O-ring seal (18) on the adapter.13. Put adapter (16) in position on the housing.End By:a. install water pump


Parts pipe Volvo Penta:

21523327
Pipe
21523327 Pipe
1372, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-A MG, D16C-D MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1140VE;
21482405
 
21482405 Pipe end
TAD1670VE; TAD1671VE; TAD1672VE, TAD570VE; TAD571VE; TAD572VE, TAD870VE; TAD871VE; TAD872VE
22203679
 
22203679 Pipe
TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE
21832751
 
21832751 Pipe
TAD840VE; TAD841VE; TAD842VE
21832762
 
21832762 Pipe
TAD840VE; TAD841VE; TAD842VE
21545821
 
21545821 Pipe
TAD840VE; TAD841VE; TAD842VE
22711734
 
22711734 Pipe
TAD840VE; TAD841VE; TAD842VE
21905286
 
21905286 Pipe
TAD870VE; TAD871VE; TAD872VE
Back to top