272056 Volvo.Penta Piston kit

Rotating gears- finger or hand entanglement. Do not service until reading the operator's manual.
The clutch warning sign is located on the clutch housing (if equipped).
Clutch warning sign.Located near batteries (if equipped):
Improper jumper cable connections can cause an explosion resulting in personal injury.Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual.
Improper lift rigging can allow load to tumble causing injury and damage.1. Use adequate spreader bar as described because center of gravity is above base lift points.2. Attach four properly rated chains from base lift points.3. Adjust chain lengths to position spreader bar over center symbol for level lift.4. Use single pint center lift arch and 5N2171 Instruction Film when present.
Located on the mounting base (if equipped) near the lifting holes.Located on the fuel tank (if equipped):
Drain fuel tank before lifting unit. Lifting this unit when fuel is present in the tank could result in separation of the tank from the base and cause personal injury or death.
Do not use the engine lifting eyes to remove the engine and generator together.
Located on engine lifting eye cover assembly. Cover assembly warning sign.General Hazard Information
Attach a DO NOT OPERATE or similar warning tag to the start switch or controls before performing maintenance or repairing the engine. These tags, SEHS7332, are available from your Caterpillar dealer. When appropriate, attach the tags at the engine and at each operator's position. Disconnect starting controls when appropriate. Do not allow unauthorized personnel on, around or in the engine unit when it is being serviced.Diesel engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.Use caution when removing filler cap, grease fittings, pressure taps, breathers or drain plugs. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquids under pressure.* Wear a hard hat, protective glasses, hearing protection and other protective equipment as required by job conditions.* Do not wear loose clothing or jewelry that can catch on controls or other parts of the engine.* Make certain all protective guards and covers are secured in place.* Use all cleaning solutions with care.* Never put maintenance fluids into glass containers since glass containers can break.* Report all needed repairs. UNLESS INSTRUCTED DIFFERENTLY, PERFORM ALL MAINTENANCE AS FOLLOWS:* Stop the engine.* Ensure the protective locks or controls are in the applied position.* Disconnect the batteries whenever performing any maintenance or before servicing the electrical system. If the engine has electric starters, disconnect and tape the battery ground leads to prevent accidental starting.* Do not attempt any repairs or adjustments to the engine or driven equipment while it is running.* Do not attempt repairs you do not understand. Use proper tools; replace or repair broken or damaged equipment.*Apply the parking brakes (if equipped). * Block or restrain the vehicle or machine, if applicable before operating or performing maintenance.* When starting an engine after repairs have been made to the fuel system or governor, make provisions for shutting off the engine's intake air supply (to stop the engine), in case there is an overspeed on startup.* Start the engine only from the operator's station. Never short across the starter terminals or the batteries as this could bypass the engine neutral-start system as well as damage the electrical system.Pressure Air and Water
Pressure air can cause personal injury. When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes.The maximum air pressure must be below 205 kPa (30 psi) and maximum water pressure must be below 275 kPa (40 psi) for cleaning purposes.Wear eye protection at all times when cleaning the cooling system. Pressurized water could cause debris and/or hot water to be blown and result in personal injury.Fluid Penetration
Always use a board or cardboard when checking for a leak. Escaping fluid under pressure, even a pin-hole size leak, can penetrate body tissue, causing serious injury or possible death.If fluid is injected into your skin, it must be treated by a doctor familiar with this type of injury immediately.Asbestos Information
This Caterpillar product and replacement parts shipped from the factory are asbestos free. Caterpillar recommends the use of only genuine Caterpillar replacement parts. If any replacement parts containing asbestos fibers are used, the following guidelines should be used in handling these parts and asbestos debris.Asbestos used in components is usually bound in a resin or sealed in some way. Normal handling is not hazardous as long as airborne dust which contains asbestos is not generated.Caution should be used to avoid breathing dust that may be generated when handling components containing asbestos fibers. If this dust is inhaled, it can be hazardous to your health.If dust, which may contain asbestos is present, there are several common sense guidelines that should be followed.* Never use compressed air for cleaning.* Avoid brushing or grinding of asbestos containing materials.* For clean up, use wet methods or a vacuum equipped with a high efficiency particulate air (HEPA) filter.* Use exhaust ventilation on permanent machining jobs.*