468986 Volvo.Penta Pressure pipe,cyl 6

1. Loosen bolts (1) and tube assembly (2) from oil pump.
The larger gear is not fastened to the pump.
2. Remove four bolts (3), locks and remove the oil pump (4). The weight of the oil pump is 35 lb. (16 kg).Install Oil Pump
1. Turn the crankshaft until the No. 1 piston is at the top center compression position. See INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR. 2. Turn both balancer shafts until the flat part on each shaft is away from the oil pan plate. Install two 3/8"-16 NC bolts (1) 11/2" long through the oil pan plate and into the holes in the balancer shafts. This will make the shafts so they will not turn. Do not tighten the bolts against the bottom of the holes in the shafts. 3. Put the oil pump (3) in position on the engine block and install the locks (left side only) and bolts that hold the oil pump in place. Surface (2) of the oil pump must be free of lock tabs.4. Remove bolts (1). Check to see that the balancer shaft timing is correct. The balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate, and No. 1 piston is at the top center compression position. 5. Put tube assembly (4) in place on oil pump and install bolts.end by:a) install oil panDisassemble Oil Pump
start by: a) remove oil pump
TYPICAL EXAMPLE1. Remove idler gear (2).2. Remove bearing (1) from gear (2) with tooling (B).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by: a) install oil pump