848330 Volvo.Penta Pressure pipe


848330 Pressure pipe Volvo.Penta TAMD103A, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D Pressure
848330 Pressure pipe Volvo Penta
Rating:
43

Buy Pressure pipe 848330 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$76.15
 

01-03-2023
5.88[2.65] Pounds
-: -
1"" Impact Extension BAR 13"" by JTC 848330
Special steel ball designed. SIZE:1" DR LENGTH:13" / 330mm || 100% Original Made By JTC || Best Quality,Fastest Shipping,Local Service Support
Number on catalog scheme: 15
 

Information:

1. Loosen clamps (1) then remove turbocharger tube (2). 2. Remove the clamps that hold breather tube (3) to the valve cover and the cylinder block. Remove breather tube (3).3. Remove the bolts that hold elbow (4) to the water temperature regulator housing. Remove elbow (4).4. Remove water lines (7) from the water pump.5. Remove engine oil cooler (5) from the water pump.6. See the illustration for the correct location of the bolts that hold the water pump to the timing gear plate. The bolts that have identification (X) only must be removed to remove the water pump.7. Remove water pump (6). Remove the gasket from the timing gear plate. The following steps are for the installation of the water pump.8. Put water pump (6) and a new gasket in position on the timing gear plate. Install the bolts that hold it in position on the timing gear plate.9. Put clean SAE 30 oil on the O-ring seals on elbow (4). Put elbow (4) in position on the water pump. Install the bolts that hold it to the water temperature regulator housing.10. Install engine oil cooler (5) on the water pump.11. Install water lines (7) on the water pump.12. Put breather tube (3) in position. Install the clamps that hold the breather tube to the valve cover and the cylinder block.13. Install turbocharger tube (2) and then tighten clamps (1).Disassemble & Assemble Water Pump
The water pump seal can be replaced without removing the water pump from the engine. An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakge or a constant flow of coolant is observed draining from the water pump housing.1. Remove O-ring seal (3) from adapter (4). Remove the adapter from housing (7). Remove the O-ring seal from the outside of the adapter.2. Remove bolt (1) and washer (2). Use tooling (A) to remove impeller (6) from shaft (13).3. Remove spring and seal (5) from the shaft.4. Remove four bolts (16) from retainer (12) that hold the shaft assembly to the pump housing. Remove O-ring seal (18) from housing (7).5. Remove gear and shaft assembly (17) from the housing. Remove bolt (15), retainer (14) and retainer (12) from the shaft assembly.6. Use a press to remove shaft (13) from the gear. Remove bearing (9), spacer (10) and bearing (11) from the shaft.7. Remove lip-type seal (8) from the housing.8. Turn the housing over, and remove ceramic ring (20) and seal (19) from the housing. The following steps are for the assembly of the water pump.9. Use 6V1541 Quick Cure Primer and clean shaft (13) and the seal counter bore in the pump housing.10. Install bearing (9), spacer (10) and bearing (11) on shaft (13).11. Put retainer (12) and gear (17) on the shaft assembly. Install retainer (14) and bolt (15) on the shaft.12. Use tooling (B) to install lip-type seal (8) in housing (7). Install seal with the lip toward the inside of the housing. Put a small amount of clean SAE 30 oil on the lip of the seal.13. Install a new O-ring seal (18) on the housing.14. Put gear and shaft assembly (17) in position in the housing. Install bolts (16) that hold retainer (12) to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (20) in position in seal (19). Use hand pressure and tool (C) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.16. Separate spring and seal (5). Use hand pressure and tool (C) to install the seal on the shaft of the gear and shaft assembly (17). Push the seal on the shaft until the seal faces make light contact. Install the spring on the shaft.17. Put impeller (6) in position on the shaft. Install washer (2) and bolt (1) that hold the impeller. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft).18. Install the O-ring seal on the outside diameter of adapter (4). Put a small amount of clean SAE 30 on the O-ring seal.19. Install O-ring seal (3) on the adapter.20. Put adapter (4) in position on the housing.End By:a. install water pump


Parts pressure Volvo Penta:

477173
Pressure equalizer
477173 Pressure equalizer
D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD103A, TA
844624
 
844624 Pressure cap, blue
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D70CHC; D70CRC; TD70CHC, MD11; MD11C; MD11D, MD21B; AQD21B, MD22A; MD22A-A; MD22L-A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TA
1542591
Pressure cap, green
1542591 Pressure cap, green
2001; 2001B; 2001AG, KAD42A; KAMD42A; HS1A, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD121G-87; TWD1210V; TWD1211V, TD30A; TD31ACE; TD40A, TD610M; TD630ME; T
863169
Pressure monitor
863169 Pressure monitor
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D12D-A MH; D12D-B MH; D12D-C MH, DH10A; DH10A 285; DH10A 360, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD4
1674083
Pressure cap
1674083 Pressure cap
1372, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GXi-B; 4.3GXi-BF; 4.3OSi-B, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E, 4.3GXi-F; 4.3GXi-FF; 4.3OSi-F, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-
848328
 
848328 Pressure pipe
TAMD103A, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D
848329
 
848329 Pressure pipe
TAMD103A, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D
848331
 
848331 Pressure pipe
TAMD103A, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D
Back to top