864285 Pressure monitor, alarm Volvo.Penta
TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
Pressure
Price: query
Rating:
Compatible models:
Volvo Penta entire parts catalog list:
- Oil- and Fuel Supervision with Installation Components. Classified. Auxiliary » 864285
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 514
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 5091
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 5111
TD100CHC; TD100CRC; TD121CHC; TD121CRC; TAD121CHC
- Oil and Fuel Supervision with Installation Components: A
- Oil and Fuel Supervision with Installation Components: B
- Oil and Fuel Supervision with Installation Components: A
- Oil and Fuel Supervision with Installation Components: B
- Oil and Fuel Supervision with Installation Components
TMD102A; TAMD102A; TAMD102D
- Oil- and Fuel Supervision with Installation Components. Classified. Auxiliary
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 514
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 5091
- Oil Supervision, Reverse Gear. Classifiable.: Twin Disc 5111
Information:
1. Drain the coolant from the radiator.2. Loosen clamps (1) and slide hose on tube. Disconnect wire (2) from elbow. 3. Loosen clamp (3) on hose. 4. Loosen clamp (4) on lower hose and slide hose from water pump. 5. Remove bolts (5) and (6) and water pump (7) from engine. Remove the O-ring seal from the water pump.Install Water Pump
1. Be sure the O-ring seal (3) and the water pump elbow gasket (1) is in position on water pump (2). With the water pump in position install four bolts. 2. Put the lower hose (5) in position and install clamp (4). 3. Slide water pump hoses in position and tighten clamps (6) and (8).4. Connect wire (7) to elbow switch.5. Fill the radiator with coolant to the correct level. See MAINTENANCE GUIDE.END BY:a) install fan and fan driveDisassemble Water Pump
START BY:a) remove water pump 1. Remove elbow (1) and cover (2) from water pump. 2. Loosen bolt (3) 6.35 mm (.25 in.). Hit the bolt with a soft hammer to remove impeller (4) from the shaft. 3. Remove spring and seal assembly (5) from the shaft (6). 4. Turn the housing over and remove bolt and washer (7). Remove bearing (8) and gear (9) as a unit. 5. Use tool (A), tooling (C) and a press to remove bearing (8) from gear (9). 6. Remove snap ring (10) with tool (B). 7. Remove bearing (11) and shaft (6) as a unit. 8. Use tool (A) and a press to remove bearing (11) from the shaft. 9. Remove the ceramic ring and seal (12) from the housing. 10. Remove the lip seal (13) from the housing with tool (C). Assemble Water Pump
1. Install lip seal in water pump housing with tooling (A). The lip of the seal must be toward the bearings. Put clean SAE 30 engine oil on the lip of the seal. 2. Use a press to install shaft (1) in bearing (2). 3. Install the shaft (1) and bearing in the housing (3). 4. Install snap ring (4) in housing with tool (B). 5. Use a press and tooling (A) to install bearing (5) on gear (6). 6. Put gear (6) and bearing in position on shaft and install bolt and washer.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surfaceof the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (7) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 8. Remove spring from the seal assembly (8). Use hand pressure and tool (C) (which is with the replacement ring) to install the seal assembly. Push seal assembly on shaft until seal faces make light contact. 9. Install spring (9). Put impeller (10) in position and install washer and bolt. Tighten bolt to a torque of 39 1 N m (28 1 lb.ft.). 10. Put gaskets in position and install elbow (11) and cover (12).END BY:a) install water pump
1. Be sure the O-ring seal (3) and the water pump elbow gasket (1) is in position on water pump (2). With the water pump in position install four bolts. 2. Put the lower hose (5) in position and install clamp (4). 3. Slide water pump hoses in position and tighten clamps (6) and (8).4. Connect wire (7) to elbow switch.5. Fill the radiator with coolant to the correct level. See MAINTENANCE GUIDE.END BY:a) install fan and fan driveDisassemble Water Pump
START BY:a) remove water pump 1. Remove elbow (1) and cover (2) from water pump. 2. Loosen bolt (3) 6.35 mm (.25 in.). Hit the bolt with a soft hammer to remove impeller (4) from the shaft. 3. Remove spring and seal assembly (5) from the shaft (6). 4. Turn the housing over and remove bolt and washer (7). Remove bearing (8) and gear (9) as a unit. 5. Use tool (A), tooling (C) and a press to remove bearing (8) from gear (9). 6. Remove snap ring (10) with tool (B). 7. Remove bearing (11) and shaft (6) as a unit. 8. Use tool (A) and a press to remove bearing (11) from the shaft. 9. Remove the ceramic ring and seal (12) from the housing. 10. Remove the lip seal (13) from the housing with tool (C). Assemble Water Pump
1. Install lip seal in water pump housing with tooling (A). The lip of the seal must be toward the bearings. Put clean SAE 30 engine oil on the lip of the seal. 2. Use a press to install shaft (1) in bearing (2). 3. Install the shaft (1) and bearing in the housing (3). 4. Install snap ring (4) in housing with tool (B). 5. Use a press and tooling (A) to install bearing (5) on gear (6). 6. Put gear (6) and bearing in position on shaft and install bolt and washer.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surfaceof the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put the ceramic ring (7) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 8. Remove spring from the seal assembly (8). Use hand pressure and tool (C) (which is with the replacement ring) to install the seal assembly. Push seal assembly on shaft until seal faces make light contact. 9. Install spring (9). Put impeller (10) in position and install washer and bolt. Tighten bolt to a torque of 39 1 N m (28 1 lb.ft.). 10. Put gaskets in position and install elbow (11) and cover (12).END BY:a) install water pump
Parts pressure Volvo Penta:
844624
844624 Pressure cap, blue
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D70CHC; D70CRC; TD70CHC, MD11; MD11C; MD11D, MD21B; AQD21B, MD22A; MD22A-A; MD22L-A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TA
1542591
1542591 Pressure cap, green
2001; 2001B; 2001AG, KAD42A; KAMD42A; HS1A, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD121G-87; TWD1210V; TWD1211V, TD30A; TD31ACE; TD40A, TD610M; TD630ME; T
863169
863169 Pressure monitor
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D12D-A MH; D12D-B MH; D12D-C MH, DH10A; DH10A 285; DH10A 360, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD4
1674083
1674083 Pressure cap
1372, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GXi-B; 4.3GXi-BF; 4.3OSi-B, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E, 4.3GXi-F; 4.3GXi-FF; 4.3OSi-F, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-
848328
848329
848330
862088
862088 Pressure gauge, oil pressure-reverse gear
TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P