872569 Volvo.Penta Pretensioning sleeve

that an electronic system malfunction is currently present. Refer to the term "Diagnostic Code" in this glossary.Aftertreatment - Aftertreatment is a system that is used to remove pollutants from exhaust gases. The system consists of the Caterpillar Regeneration System, a diesel oxidation catalyst and a diesel particulate filter.Aftertreatment Regeneration Device (ARD) - This item is sometimes referred to as the Caterpillar Regeneration System. The ARD is a device that intermittently raises the temperature of the exhaust gases in order to regenerate the diesel particulate filter.Air-To-Air Aftercooler - An air-to-air aftercooler is a device that is used on turbocharged engines in order to cool inlet air that has undergone compression. The inlet air is cooled after the inlet air passes through the turbocharger. The inlet air is passed through an aftercooler (heat exchanger) that uses ambient air for cooling. The inlet air that has been cooled advances to the inlet manifold. Alternating Current (AC) - Alternating current is an electric current that reverses direction at a regular interval that is reoccurring.ARD Fuel Pump - The ARD fuel pump provides high-pressure fuel to the fuel system for the aftertreatment regeneration device.Before Top Center (BTC) - BTC is the 180 degrees of crankshaft rotation before the piston reaches the top center position in the normal direction of rotation.Boost Pressure - The difference between the turbocharger outlet pressure and atmospheric pressure is commonly referred to as boost pressure. The sensor for the intake manifold air pressure measures the amount of boost.Breakout Harness - The breakout harness is a test harness that is designed to connect into the engine harness. This connection allows a normal circuit operation and the connection simultaneously provides a Breakout T in order to measure the signals.Bypass Circuit - A bypass circuit is a circuit that is used as a substitute circuit for an existing circuit. A bypass circuit is typically used as a test circuit.CAN Data Link (see also J1939 CAN Data Link) - The CAN Data Link is a serial communications port that is used for communication with other microprocessor-based devices.Caterpillar NOx Reduction System - The Caterpillar NOx Reduction System recycles a portion of the exhaust gases back into the inlet air in order to reduce the formation of nitrous oxide (NOx) in the combustion process. The recycled exhaust gas passes through a cooler before being introduced into the inlet air.Caterpillar Regeneration System - Refer to "Aftertreatment Regeneration Device".Clean Emissions Module (CEM) - Refer to "Aftertreatment".Code - Refer to "Diagnostic Code" or "Event Code".Cold Mode - Cold mode is a mode for cold starting and for cold engine operation. This mode is used for engine protection, reduced smoke emissions, and faster warm-up time.Communication Adapter Tool - The communication adapter provides a communication link between the ECM and the Electronic Service Tool.Component Identifier (CID) - The CID is a number that identifies the specific component of the electronic control system that has experienced a diagnostic code.Coolant Temperature Sensor - The coolant temperature sensor detects the engine coolant temperature for all normal operating conditions and for engine monitoring.Customer Specified Parameters - A customer specified parameter is a parameter that can be changed in the ECM with the Electronic Service Tool. A customer specified parameter's value is set by the customer. These parameters are protected by customer passwords.Data Link - The Data Link is a serial communication port that is used for communication with other microprocessor-based devices.Derate - Certain engine conditions will generate event codes. Also, engine derates may be applied. The map for the engine derate is programmed into the ECM software. The derate can be one or more of three types: reduction of rated power, reduction of rated engine speed and reduction of rated machine speed for OEM products.Desired Engine Speed - The desired engine speed is input to the electronic governor within the ECM. The electronic governor uses the signal from the throttle position sensor, the engine speed/timing sensor, and other sensors in order to determine the desired engine speed.Diagnostic Trouble Code - A diagnostic trouble code is sometimes referred to as a fault code. These codes indicate an electronic system malfunction.Diagnostic Lamp - A diagnostic lamp is sometimes called the check engine lamp. The diagnostic lamp is used to warn the operator of the presence of an active diagnostic code. The lamp may not be included in all applications.Diesel Oxidation Catalyst - The Diesel Oxidation Catalyst is also known as the (DOC). The DOC is a device in the exhaust system that oxidizes certain elements in the exhaust gases. These elements can include carbon monoxide (CO), hydrocarbons and the soluble organic fraction (SOF) of particulate matter.Diesel Particulate Filter - The Diesel Particulate Filter (DPF) filters particulates from the exhaust gases. When the particulates have built up on the internal surfaces of the DPF, the temperature of the exhaust gas is raised by the Aftertreatment Regeneration Device (ARD) in order to burn off the particulates. This regeneration process prevents the DPF from becoming blocked. The regeneration process therefore allows the DPF to continue to operate efficiently.Digital Sensor Return - The common line (ground) from the ECM is used as ground for the digital sensors.Digital Sensors - Digital sensors produce a pulse width modulated signal. Digital sensors are supplied with power from the ECM.Digital Sensor Supply - The power supply for the digital sensors is provided by the ECM.Direct Current (DC) - Direct current is the type of current that flows consistently in only one direction.DT, DT Connector, or Deutsch DT - This is a type of connector that is used on the engines. The connectors are manufactured by Deutsch.Duty Cycle - Refer to "Pulse Width Modulation".Electronic Engine Control - The electronic engine control is a complete electronic system. The electronic engine control monitors the engine operation under all conditions. The electronic engine control also controls the engine operation under all conditions.Engine Control Module (ECM) - The ECM is the control computer of the engine. The ECM provides power to the electronics. The ECM monitors data that is