7744470_025 Volvo.Penta Propeller


7744470_025 Propeller Volvo.Penta DP-E; SP-E; TSK DP-E Propeller
7744470_025 Propeller Volvo Penta
Rating:
18

Buy Propeller 7744470_025 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Compatible models:

DP-E; SP-E; TSK DP-E   Volvo.Penta

Volvo Penta entire parts catalog list:

DP-E; SP-E; TSK DP-E

Information:


Illustration 1 g00879007
Table 1
Pin Assignment on the Sensor     Connection    
Pin A     Switched Positive Battery    
Pin B     Negative Battery Bus Bar    
Pin C     Throttle Position Signal    The output of the sensor is a constant frequency signal with a pulse width that varies with the throttle position. The pulse width measures the duty cycle. The Pulse Width Modulated signal (PWM) is expressed as a percentage of the duty cycle. This percentage is between 0 and 100 percent. The TPS will produce a minimum duty cycle when the throttle is released. The TPS will produce a maximum duty cycle when the throttle is fully actuated.
Illustration 2 g00751431
Duty Cycle
Illustration 3 g00751478
Definition of PWM
Illustration 4 g00766798
Percent of Throttle Position versus PWM Input
Table 2
Throttle Position     Duty Cycle     Nominal Duty Cycle    
Low idle     5-10%     8%    
High idle     90-95%     92%    PWM Input RequirementsThe following criteria are required for the correct operations of a throttle position sensor that is not Caterpillar:"Activepull up/pull down with output protection""Sensor stop"
Low stop 7.5% 2.5%
High stop 92.5% 2.5%"Output frequency"
Minimum of 300 Hz
Nominal of 500 Hz
Maximum of 700 Hz"High output voltage"
Minimum of 4.5 VDC
Maximum of 32 VDC"Low output voltage"
Minimum of -0.3 VDC
Maximum of 0.5 VDC"Sink current"
-1.5 mA"Source current"
-2.0 mANote: The sourcing driver must be capable of sinking 1.5 mA if the output voltage of the output driver is less than 13.0 VDC."Output linearity"
2.5 % duty cycle versus throttle lever position
Illustration 5 g00762874
Simulated Load for the ECM
Illustration 6 g00885265
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Check the connectors and wiring for the following problems: damage, corrosion, abrasion and incorrect attachment. Pay close attention to the following areas:
J1/P1 ECM connector
J3/P3 Customer connector
J35/P35 Throttle Position Sensor (Port)
J35/P35 Throttle Position Sensor (STBD)Refer to Troubleshooting, "Electrical Connectors - Inspect" for more information.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.Clear all logged diagnostic codes. Stop.Test Step 2. Check the Voltage at the Sensor
Turn the keyswitch to the ON position. The engine should be OFF.
Measure the voltage between P35:A and P35:B (Port).
Measure the voltage between P35:A and P35:B (STBD).Expected Result:The supply voltage should be between 11.0 VDC and 13.5 VDC for a 12 Volt system and the supply voltage should be between 22.0 VDC and 27.0 VDC for a 24 Volt system.Results:
OK - The supply voltage is reaching the sensors. Proceed to Test Step 3.
Not OK - Proceed to Test Step 4.Test Step 3. Check the Throttle Position Sensor Duty Cycle at the Sensor
Turn the keyswitch to the OFF position.
Remove the signal wire from Pin C of the throttle position sensor.
Set the digital multimeter to the VDC.
Press the Hz button twice in order to activate the display that will show the symbol for percent.
Place the positive probe of the multimeter on Pin C of the throttle position sensor.
Place the negative probe of the multimeter on Pin B of the throttle position sensor.
Move the throttle from low idle to high idle and monitor the duty cycle output of the throttle position sensor on the multimeter.Expected Result:The duty cycle should be between 5.0 percent and 10.0 percent when the throttle is at low idle. The duty cycle should be 90.0 percent to 95.0 percent when the throttle is at high idle.Results:
OK - A valid signal appears at the sensor connector. Proceed to Test Step 5.
Not OK - The duty cycle is out of the range.Repair: Perform the following diagnostic procedure.Refer to Troubleshooting, "Throttle Position Sensor - Calibrate". Stop.Test Step 4. Measure No-Load Battery Voltage
Measure the no-load battery voltage at the battery posts.Note: Loa


Parts propeller Volvo Penta:

3851334
Propeller nut
3851334 Propeller nut
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
854784
Propeller, rear
854784 Propeller, rear
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
854769
Propeller
854769 Propeller
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
3857465
Propeller, rear
3857465 Propeller, rear
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
3857467
Propeller, rear
3857467 Propeller, rear
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
3857468
Propeller, rear
3857468 Propeller, rear
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
21924266
Propeller kit
21924266 Propeller kit
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
21924267
Propeller kit
21924267 Propeller kit
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
Back to top