813296 Volvo.Penta Propeller

Introduction
This Special Instruction outlines the procedures to install the new bolted engine hood bracket on excavators with a composite engine hood. The new bolted engine hood bracket replaces the former non-bolted bracket. The non-bolted engine hood bracket may fail to adhere to the composite engine hood. The former engine hood bracket had been secured to the composite engine hood by an adhesive. The new bolted hood bracket prevents the separation of the bracket from the composite hood. This rework procedure will extend the service life of the engine hood bracket on machines with a composite hood.The new bolted engine hood bracket replaces the former non-bolted bracket on the following excavator models that are equipped with a composite engine hood: 320B, 322B, 325B and 330B. The bolted bracket is effective with the excavator models that are listed in Table 1. The new bracket is adaptable to the above listed models with a composite engine hood.Do not perform any installation procedures until you have read the information in this publication.
Table 1
Support Bracket (Bolted)
Used For the Composite Engine Hood    
Model Number     Effective Serial Number    
320B     7JR1825-Up
1XS821-Up
2AS620-Up
5MS510-Up
9WS184-Up
6LW328-Up
3YZ648-Up    
322B     1ZS491-Up
2ES839-Up    
325B     6DN1001-Up
8FN1017-Up
4DS216-Up
5BS227-Up    
330B     3YR878-Up
5LR614-Up
4RS427-Up
5LS232-Up    Also refer to the appropriate Parts Manual, Operation and Maintenance Manual, and Service Manual. Installation of the Hood Support Bracket for the 320B Excavator
Required Parts
The parts that are required to install the new support bracket are listed in Table 2.
Table 2
320B Excavators With A Composite Engine Hood    
Qty     New
Part Number     Description     Former
Part Number    
1     174-4435     Bracket Assembly     135-0727    
6     166-1222     Hex Socket Drive Screw     none    
2     174-6191     Spacer     none    This rework procedure is for the 320B Excavators that are equipped with a composite engine hood.Note: Perform the following tasks before you begin this rework procedure:
Move the machine to a flat surface area.
Shut off the engine.
Allow the exhaust pipe to cool.
When the hood support bracket is no longer attached to the engine hood, the hood support can not be used to hold the engine hood in its open position.You must secure the engine hood with an additional holding device while performing the support bracket installation.
Illustration 1 g00651180
This is a typical example of an hood support bracket that is non-bolted. (1) hood support bracket (2) hood support (3) Composite engine hood
When the engine hood bracket (1) separates from the composite engine hood, the hood support (2) is unable to secure the engine hood (3) in the open position. Secure the engine hood with an additional holding device, when you install the new support bracket.
Illustration 2 g00652200
This is a typical example of a composite engine hood with a non-bolted support bracket. (1) hood support bracket (2) hood support (4) Cotter pin (5) Clevis pin (6) Washer
Remove cotter pin (4) from clevis pin (5). Remove the pin (5) and remove the washer (6) from the engine hood bracket (1). Release the hood support (2) from the bracket (1). The cotter pin (4), the pin (5), the washer (6), and the support (2) will be reused. You may discard the engine hood bracket (1).
Illustration 3 g00652309
This is the top view of the composite engine hood.
Illustration 4 g00652713
This is a typical example of a composite engine hood and the location for the new engine hood support bracket bolt holes. (A) 463 mm (18.25 inch) (B) 610 mm (24.0 inch) (C) 757 mm (29.75 inch) (D) 46.6 mm (1.83 inch) (E) 130 mm (5.12 inch) (F) 9 mm (0.35 inch) bolt holes (3) Top of the engine hood
The new hood support bracket is bolted. Drill six 9 mm (0.35 inch) holes into the composite engine hood for the installation of the new bracket. Refer to Illustration 3 and Illustration 4 in order to determine the location of the bolt holes.
Illustration 5 g00653088
Typical example of the components that are required to install the new hood support bracket (3) Composite engine hood (7) New bolted hood support bracket (8,9) Hex socket drive screws and spacers
Position the new hood support bracket (7) at the drilled holes on the engine hood. Install the two spacers (9) and the six hex socket drive screws (8) that secure the support bracket (7) to the engine hood (3), as Illustration 5 shows.
Torque the hex socket drive screws (8) to 28 7 N m (21 5 lb ft).