860025 Pulley Volvo.Penta
MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B
Pulley
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$10.51
29-08-2017
.63[0.00] pounds
Dorman - A: Dorman - Autograde
Dorman 860-025 Hex Head Cap Screw
Dorman||860-025||Hex Screws and Nuts
Dorman||860-025||Hex Screws and Nuts
Compatible models:
Volvo Penta entire parts catalog list:
- Pulley: 860026 » 860025
TMD41A; TMD41B; D41A; D41B; TAMD41A; TAMD41B; AQAD41A; AD41A; AD41B; 290A; DP-A; DP-B; DP-A1; DP-B1; SP-A; SP-A1; AD41BJ; AD41; AD41P-B; D41; TAMD41
TMD41B; D41B; TAMD41B; AD41B; AD41BJ
Information:
Table 1
3512 Oil and Filter Change Intervals
Change Interval and Sump Configuration 250 Hours Shallow Sump 500 Hours Standard Sump 1000 Hours Deep Sump
Capacity Gallons Liters Gallons Liters Gallons Liters
Factory Fill 52 197 85 322 165 625
Refill with Filter Change 41 155 82 311 162 614
Sump Only Refill without Filter Change 36 136 78 296 158 599
Volume between "Add" and "Full" Marks 6 23 18 68 28 106
Table 2
3516 Oil and Filter Change Intervals
Change Interval and Sump Configuration 250 Hours Shallow Sump 1000 Hours Deep Sump
Capacity Gallons Liters Gallons Liters
Factory Fill 57 216 214 811
Refill with Filter Change 50 190 211 800
Sump Only Refill without Filter Change 42 159 206 781
Volume between "Add" and "Full" Marks 5 19 36 136 Drain the Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Do not drain the oil when the engine is cold. As the oil cools, waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase when the oil is warm. This method allows proper draining of the waste particles that are suspended in the oil.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.
Drain the oil according to the equipment on the engine.Note: Drain the oil into a suitable container. DO NOT drain the oil into the bilge sump. Dispose of the oil according to local regulations.
Illustration 1 g00574534
Oil drain plug
Note: If a suction device is used, ensure that the suction device is clean to keep dirt out of the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
If the engine does not have a drain valve or a pump, remove an oil drain plug. Allow the oil to drain. After the oil has drained, clean the drain plug and clean the fitting for the drain plug. Install the drain plug. Tighten the drain plug to 145 15 N m (105 10 lb ft).
If the engine has an oil drain valve, open the valve. After the oil has drained, close the valve.
If the engine has a pump for removing dirty oil, connect a hose to the outlet of the pump. Place the hose in a suitable container. Open the valve for the drain line. Turn the two marks on the valve so that one mark points to the pump and the second mark points to the drain line. Operate the pump until the crankcase is empty. Close the valve to the drain line. Disconnect the hose.
If the oil drain valve has a “quick connect” coupling, attach the coupling. Open the drain valve to drain the crankcase. After the oil has drained, close the drain valve. Disconnect the coupling.
Replace the engine oil filter elements before filling the crankcase with new oil.Replace the Oil Filter Elements
Replace the engine oil filters when any of the following conditions occur:
Every oil change
The engine oil filter differential pressure reaches 103 kPa (15 psi).
The oil filter elements have been used for 1000 service hours.Note: Do not attempt to clean the used oil filters. Used oil filters will retain waste particles. The used oil filters would not filter the oil properly.Service tools are available to aid in the service of oil filters. Consult your Cat dealer for the part names and the part numbers. Follow the instructions that are supplied with the service tools. If the service tools are not used, perform the following appropriate procedure.Replacing the Engine Oil Filters With the Engine Stopped
Hot oil and components can cause personal injury.
Parts pulley Volvo Penta:
843314
843314 Pulley
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, MD40A; TMD40A; TMD40B, TMD41A; TMD41B; D41A
842710
842710 Pulley
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, MD40A; TMD40A; TMD40B, TMD41A; TMD41B; D41A
1542235
1542235 Pulley
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A, TMD41A; TMD4
841812
841812 Pulley
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, MD120A; MD120AK; TMD120A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A;
858191
858191 Pulley
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B
858257
858257 Pulley kit
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B
838596
838596 Pulley
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B
860026
860026 Pulley
MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B