825978 Volvo.Penta Pump shaft

Introduction
The purpose of this special instruction letter is to provide dealers and customers with information regarding the control panel kits available for the various work over applications. The panel kits are for the 12-volt and 24-volt applications.Note: Power for the panel group must come directly from the battery.Note: Do NOT connect the positive (+) wire of the panel group to the starter terminal. Connecting the positive (+) wire to the starter terminal may cause the panel group to malfunction. Incorrect wiring could also damage the components inside the panel. Connect the positive (+) wire directly to the battery.Note: Do NOT connect the negative (-) wire on the panel group to the starter, the chassis, or the engine ground. Incorrect wiring may also cause the panel group to malfunction. The negative (-) wire on the panel group must be connected to the battery through the battery disconnect switch.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Most accidents that involve product operation, maintenance, and repair are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.Improper operation, maintenance, or repair of this product may be dangerous. Improper operation, maintenance, or repair of this product may result in injury or death.Do not operate or perform any maintenance or repair on this product until you have read and understood the operation, maintenance, and repair information.Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are not all inclusive. If a tool, procedure, work method, or an operating technique that is not recommended by Caterpillar is used, make sure that it is safe for you and for other people. It is important to be sure that the product will not be damaged. Ensure that the product will not be made unsafe by the procedures that are used.Installation Procedure for Control Panel Kits
Illustration 1 g02726243
(1) Starter motor (2) To start relay (3) Battery (4) Battery disconnect switch (5) Chassis (6) Control panel
Illustration 2 g02726417
Workover Rig engine and transmission wiring and control panel - Block diagram (1) Ignition switch (2) Tach (3) Engine oil pressure (4) Engine coolant temperature (5) Messenger (6) Primary shifter (7) Shifter selector with mode lamps (8) Engine warning (9) Transmission warning (10) Check transmission warning (11) Service brake pressure switch (12) Parking brake pressure switch (13) Engine ECM (14) Junction box (15) Cab harness (16) ECM shutdown relay (17) Fuse box 10 ckt (18) Starter relay (19) Backup alarm relay (20) 9 pin diagnostic connector (21) Air throttle pressure (22) Starter and starter wire (23) Battery and battery wire (24) ECM to pig tails (25) Air shutdown (26) Low coolant switch input (27) Engine ECM "J1" harness (28) Transmission OEM harness (29) Transmission PEM connector (30) Sand drum emergency stop (31) < 10 m (33 ft) (32) < 0.7 m (2.3 ft) (33) Backup alarm (34) Backup alarm harness (35) Backup alarm (36) Platform harness (37) Platform panel (38) Engine warning (39) Transmission warning (40) Check transmission warning (41) Lockup clutch lamp (42) Emergency stop (43) Secondary shifterInstallation Procedure for 12-Volt Kits
Note: The panel kit is packaged with all necessary parts for operation on a work over unit.12 Volt Panel Kit for TH Transmissions
Table 1
359-4130 Instrument Panel Gp    
Part Number    Part Description    
110-7887     Start Switch Gp    
112-4073     Pressure Switch Gp    
172-7071     Pressure Switch Gp    
213-9100     Travel Alarm Gp    
257-4134     Rocker Switch    
274-8068     Interface Module Gp    
275-2081     Coolant Temperature Gauge Gp    
275-2096     Engine Oil Pressure Gauge Gp    
275-2103     Electric Tachometer Gp    
298-3860     Transmission Control Gp    
301-3081     Display Module Gp    
328-2149     Transmission Harness As    
328-2150     Platform Harness As    
332-3972     Indicator Lamp    
332-7684     Instrument Panel Gp    
337-5437     Indicator Lamp    
350-3507     Alarm Harness As    
359-1917     Electronic Panel Gp    
359-1919     Panel Harness As    
361-1984     Panel Harness As    Note: Refer to 359-1918 Schematic The 359-4130 Instrument Panel Gp TH is connected to the engine ECM, transmission ECM, and cab mounted components