21034347 Volvo.Penta Push rod

1. Remove the pipe to the aftercooler housing.2. Disconnect turbocharger oil drain lines (5) and (6).3. Disconnect turbocharger oil supply lines (2) and (3).4. Bend the tabs down. Remove two bolts (4).5. Remove two clamps (1). Remove the tube. 6. Use two people or attach a hoist to turbocharger (7). The weight of the turbocharger is 30 kg (66 lb).7. Remove four bolts (9). Remove the turbocharger.8. Use two people or attach a hoist to turbocharger (8). The weight of the turbocharger is 30 kg (66 lb).9. Remove four bolts (10). Remove the turbocharger.Install Turbochargers (Engine With Four Turbochargers)
Installation is shown for one side only. The procedure is the same for both sides.
Make sure the 2P-2333 Manifold Sealer does not get on the inside of the pipes. Damage to the turbocharger could be the result if the manifold sealer gets on the impeller on the turbocharger.
1. Put 2P-2333 Manifold Sealer on the male ends of turbochargers (8).2. Use a hoist or two people to install turbocharger (8). Use a new gasket between turbocharger (8) and the elbow.3. Apply 5P-3931 Anti-Seize Compound to four bolts (10). Install the bolts.4. Put 2P-2333 Manifold Sealer on the male ends of turbocharger (7).5. Use a hoist or two people to install turbocharger (7). Use a new gasket between turbocharger (7) and the elbow.6. Apply 5P-3931 Anti-Seize Compound to four bolts (9). Install the bolts. 7. Lubricate the O-ring seals for the pipe with glycerin.8. Install the pipe with two clamps (1). Tighten the wrap around clamp to a torque of 7.0 1.5 N m (5.00 1.00 lb ft). Tighten the bolts on the half clamp to standard torque.9. Install two bolts (4). Bend the tabs down.10. Install the pipe to the aftercooler housing.11. Use new gaskets and attach oil drain lines (5) and (6).12. Use new gaskets and attach oil supply lines (2) and (3).Disassemble Turbocharger (S3B)
Start By:a. remove turbocharger 1. Install the turbocharger on Tool (A). Put alignment marks on the three housings of the turbocharger for correct installation. Remove "V" clamp (2) and compressor housing (1). 2. Remove "V" clamp (3). Remove cartridge housing (5) from turbine housing (4).
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
3. Install Tool (C) in Tool (B). Put the cartridge assembly in Tool (C) as shown. Use Tool (D) to remove the nut that holds compressor wheel (6). 4. Put the cartridge assembly in Tool (E) and use a press (if necessary) to remove compressor wheel (6) from the turbine wheel and shaft assembly. Do not let the turbine wheel and shaft assembly fall during removal of the compressor wheel from the turbine wheel and shaft. 5. Remove seal ring (7) and shroud (8) from turbine wheel and shaft assembly (9). 6. Bend the tabs of the locks from bolts (10) and remove the bolts and locks.7. Remove backplate assembly (11) from the cartridge housing. 8. Remove spacer (12) from backplate assembly (11). Remove seal rings (13) from spacer (12). 9. Remove collar (14), thrust bearing (15) and O-ring seal (16) from the cartridge housing. 10. Remove top bearing (17) and the washer from the top cartridge housing. Put a long dye mark on the top face of bearing (17).11. Use Tool (F) and remove the two rings that hold the top and bottom bearings in position. Remove the bottom bearings and washer. Put a short dye mark on the bearing. The dye marks are used for identification of the bearings when they are installed.12. Use Tool (F) and remove the last ring that holds the bottom bearing in position on the cartridge housing.13. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction, SMHS6854 for Turbocharger Reconditioning. Also see Guidelines For Reusable Parts, SEBF8018.Assemble Turbocharger (S3B)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and debris.2. Put clean engine oil on all parts of the cartridge assembly.
Rings (18), (21) and (22) must be installed with the round edge of the outside diameter of the rings toward the bearings.
3. Install ring (21) in the cartridge housing with Tool (F).4. Install washer (19) and bearing (20) in the cartridge housing. Make sure the short dye mark on bearing (20) is up. 5. Install rings (18) and (22) in the cartridge housing with Tool (F). 6. Install washer (23). 7. Install bearing (17) with the long dye mark up. 8. Install bearing (15). Align the pins in the cartridge with the holes in the bearing. Be sure the three lubrication grooves are facing up as shown. 9. Install collar (14) with the small diameter toward bearing (15). Put O-ring (16) in position. Put 6V-2055 High Vacuum Grease in the grooves of spacer (12) to one half or more of the depth of the grooves all the way around.10. Use Tool (G) to install seal rings (13) on to spacer (12). 11. Install spacer (12) into backplate (11). Be sure the chamfered end of spacer (12) is toward the inside of the cartridge assembly when the backplate assembly is installed. 12. Install backplate assembly (11) on the cartridge assembly with the oil hole in the backplate assembly in alignment with the oil hole in the cartridge housing. 13. Install locks and bolts (10) that hold backplate assembly (11) in position. Tighten the bolts to a torque of 10 1 N m (90 9 lb in). Put 6V-2055 High Vacuum Grease in the groove for seal ring (7) at assembly to one half or more of the depth of the groove all the way around.14. Use Tool (G) to install shroud (8) and seal ring (7) onto turbine wheel and shaft assembly (9).