3853483 Volvo.Penta Push rod, intake valve


3853483 Push rod, intake valve Volvo.Penta 7.4GLPHUS; 7.4GIPHUSCE; 7.4GSIXHUS, 7.4GLPMDA; 7.4GLPMDM; 8.2GLPMDA, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM Push
3853483 Push rod, intake valve Volvo Penta
Rating:
48

Buy Push rod, intake valve 3853483 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Volvo Penta entire parts catalog list:

7.4GLPHUS; 7.4GIPHUSCE; 7.4GSIXHUS; 7.4GLIHUB; 7.4GIIHUBCE
7.4GLPMDA; 7.4GLPMDM; 8.2GLPMDA; 8.2GLPMDM; 7.4GLIMDA; 7.4GLIMDM; 8.2GLIMDA; 8.2GLIMDM
7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM; 7.4GLPNCB; 7.4GIINCCCE; 7.4GIINCSCE; 7.4GIPNCACE; 7.4GIPNCBCE; 7.4GIPNCMCE; 7.4GIPNCSCE; 7.4GLINCC; 7.4GLI

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, to the piston rings, to the outer surface of the piston and to the bearing shells for the connecting rod. Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure. Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g02013213
Install Tooling (B) onto piston (4). Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin. Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g02512136
Install connecting rod cap (2) onto connecting rod (1). Note: Ensure that etched Number (X) on connecting rod cap (2) matches etched Number (X) on connecting rod (3). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts in order to secure the connecting rod cap.
Install new bolts (1) to connecting rod (3). Tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 9 in order to install the remaining pistons and connecting rods. End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts push Volvo Penta:

3853484
 
3853484 Push rod, exhaust valve
7.4GLPHUS; 7.4GIPHUSCE; 7.4GSIXHUS, 7.4GLPMDA; 7.4GLPMDM; 8.2GLPMDA, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM
3853526
 
3853526 Push rod, intake valve
7.4GLPHUS; 7.4GIPHUSCE; 7.4GSIXHUS, 7.4GLPLKD; 7.4GLPLKE; 7.4GIPLKDCE, 7.4GLPMDA; 7.4GLPMDM; 8.2GLPMDA, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM
3853525
 
3853525 Push rod, exhaust valve
7.4GLPHUS; 7.4GIPHUSCE; 7.4GSIXHUS, 7.4GLPLKD; 7.4GLPLKE; 7.4GIPLKDCE, 7.4GLPMDA; 7.4GLPMDM; 8.2GLPMDA, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM
3856029
Push rod, intake valve
3856029 Push rod, intake valve
7.4GLPLKD; 7.4GLPLKE; 7.4GIPLKDCE, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM
3856030
 
3856030 Push rod, exhaust valve
7.4GLPLKD; 7.4GLPLKE; 7.4GIPLKDCE, 7.4GLPNCA; 7.4GLPNCS; 7.4GLPNCM
Back to top