7742830_045 radiator and installation comps Volvo.Penta
D70B; D70B PP; D70B K
radiator

Price: query
Rating:
Compatible models:
D70B; D70B PP; D70B K
Volvo.Penta
Volvo Penta entire parts catalog list:
- Cooling System, Induction and Exhaust Manifold: A » 7742830_045
- Cooling System, Induction and Exhaust Manifold: B
- Fan, Fan-and Belt Protection with Inst.components, MO-XXXXX/33071: A
- Fan, Fan-and Belt Protection with Inst.components, MO-XXXXX/33071: B
- Fan-and Belt Protection with Installation COMP.MOXXXXX/33072-: A
- Fan-and Belt Protection with Installation COMP.MOXXXXX/33072-: B
- Fan-and Belt Protection with Installation Comp, MOXXXXX/40848-
Information:
Introduction
This Special Instruction contains information for the installation of the upgrade fuel kit for dynamic gas blending. The installation applies to the 3516B and 3512B Diesel Engines. The information in this publication focuses on removing the old components, installing the new components, and engine components. Some engine components may not be original components.Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.
Table 1
Related Publications for Reference
Media Number Publication Type
REHS7487 Special Instruction
UENR1210 Systems Operation Troubleshooting Testing and Adjusting
LEBE0007 Application and Installation Guide
SEBU9019 Operation and Maintenance Manual (for drilling)
KENR9744 Troubleshooting (for Drilling) Note: The EMCP panel does not come with a mounting bracket. A mounting bracket must be fabricated. Refer to the ECMP publication Application and Installation Guide, LEBE0007 for best mounting practices. Modifying the old mounting location brackets is not acceptable for mounting of the new panel.Note: The following instructions will allow the EMCP to be configured properly if the following configuration is true. The engine must be configured for remote start and stop as described in the ""Remote Start"" section of this publication. If the configuration is not the same as described, refer to the Application and Installation Guide, LEBE0007 to ensure the proper configuration.Use the latest version of Cat ET. The current version of Cat ET is "2014B".
Illustration 1 g03581530
Typical example of a unit
Illustration 2 g03581527
Typical example of a unitImportant Safety Information
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe. Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or repair procedures used.
Power source must be disconnected before working on equipment.Failure to disconnect power source could result in injury or death.
High voltage may be present. The power source must be disconnected before working on the equipment. Failure to disconnect the power source could result in injury or death. Verify that the equipment is not energized before performing any maintenance. This work must be performed by trained personnel with correct tools and procedures.
Personal injury or death can result from high voltage.Moisture can create paths of electrical conductivity.Make sure that the electrical system is OFF. Lock out the starting controls and tag the controls "DO NOT OPERATE".
Common Parts for All Applications
Table 2 provides information that is related to all applications. Table 7, 8, 9, 10, and 11 contain information for specific applications.Note: The part numbers listed in the following tables may not be the same part numbers that are used in your application. That is, the part numbers may be different due to the kV rating of the application.
Table 2
Qty Part Number Part Name Description
This Special Instruction contains information for the installation of the upgrade fuel kit for dynamic gas blending. The installation applies to the 3516B and 3512B Diesel Engines. The information in this publication focuses on removing the old components, installing the new components, and engine components. Some engine components may not be original components.Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.
Table 1
Related Publications for Reference
Media Number Publication Type
REHS7487 Special Instruction
UENR1210 Systems Operation Troubleshooting Testing and Adjusting
LEBE0007 Application and Installation Guide
SEBU9019 Operation and Maintenance Manual (for drilling)
KENR9744 Troubleshooting (for Drilling) Note: The EMCP panel does not come with a mounting bracket. A mounting bracket must be fabricated. Refer to the ECMP publication Application and Installation Guide, LEBE0007 for best mounting practices. Modifying the old mounting location brackets is not acceptable for mounting of the new panel.Note: The following instructions will allow the EMCP to be configured properly if the following configuration is true. The engine must be configured for remote start and stop as described in the ""Remote Start"" section of this publication. If the configuration is not the same as described, refer to the Application and Installation Guide, LEBE0007 to ensure the proper configuration.Use the latest version of Cat ET. The current version of Cat ET is "2014B".
Illustration 1 g03581530
Typical example of a unit
Illustration 2 g03581527
Typical example of a unitImportant Safety Information
Do not perform any procedure in this Special Instruction until you have read this Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools in order to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe. Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or repair procedures used.
Power source must be disconnected before working on equipment.Failure to disconnect power source could result in injury or death.
High voltage may be present. The power source must be disconnected before working on the equipment. Failure to disconnect the power source could result in injury or death. Verify that the equipment is not energized before performing any maintenance. This work must be performed by trained personnel with correct tools and procedures.
Personal injury or death can result from high voltage.Moisture can create paths of electrical conductivity.Make sure that the electrical system is OFF. Lock out the starting controls and tag the controls "DO NOT OPERATE".
Common Parts for All Applications
Table 2 provides information that is related to all applications. Table 7, 8, 9, 10, and 11 contain information for specific applications.Note: The part numbers listed in the following tables may not be the same part numbers that are used in your application. That is, the part numbers may be different due to the kV rating of the application.
Table 2
Qty Part Number Part Name Description
Parts radiator Volvo Penta:
344753
344753 Radiator cap
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, TAD1030G; TD1010G; TWD1010G, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TAMD71B; TAMD73P-A; TAMD73WJ-A, TD100CHC;
821128
821128 Radiator hose
D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, TAMD60C, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP
821160
821160 Radiator
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, TD100CHC; TD100CRC; TD121CHC, TD30A; TD31ACE; TD40A, TMD102A; TAMD102A; TAMD102D
821684
821684 Radiator hose
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, TD100CHC; TD100CRC; TD121CHC, TMD102A; TAMD102A; TAMD102D
323685
323685 Radiator cap insert
AQ115A; AQ115B; AQ130, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, TD120AHC; TD120ARC; TAD120AHC, TD120C, TD60A; TD60B; TD60B PP, TID120FPP; TID120FG; TD120G
342761
822721
822722