877306 Volvo.Penta Relay


877306 Relay Volvo.Penta TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TID162AG; TID162AGP; TID162AP, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D Relay
877306 Relay Volvo Penta
Rating:
88

Buy Relay 877306 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Volvo Penta entire parts catalog list:

TAD1630P; TWD1630P; TWD1630PP; TAD1630PB
TAD1630V; TWD1630V
TAMD103A
TAMD122A; TMD122A; TAMD122P-A; TAMD122P-B; TAMD122P-C; TMD122A/C; TAMD122AF
TID162AG; TID162AGP; TID162AP; TID162APB
TMD102A; TAMD102A; TAMD102D
TMD121C; TAMD121C; TAMD121D; TAMD122C; TAMD122D

Information:

1. Remove two bolts (3), clamp (2) and exhaust pipe (1).2. Loosen clamp (8).3. Disconnect air inlet hose (9).4. Remove four bolts (5). Check gasket and seal on tube assembly for wear or damage. Replace if necessary.5. Remove two bolts (7), oil tube (6) and gasket. Check gasket and seal for wear or damage. Replace if necessary.6. Remove two bolts (12), oil tube (11) and gasket. Check gasket and seal for wear or damage. Replace if necessary.7. Remove six bolts (10).8. Remove turbocharger (4) and gasket. Check for wear or damage. Replace if necessary. For installation of the turbocharger, reverse the removal steps.End By:a. install mufflerDisassemble & Assemble Turbocharger
Start By:a. remove turbocharger 1. Install the turbocharger on tool (A).2. Put alignment marks on the two housings and cartridge assembly of the turbocharger for correct alignment during assembly.3. Loosen clamp (3), and remove compressor housing (4) from cartridge assembly (2).4. Loosen the remaining clamp, and remove cartridge assembly (2) from turbine housing (1). 5. Put the cartridge group (shown in the illustration) with nut (16) up in tool (B). Use a 5S9566 Sliding T-Wrench and a universal socket to remove nut (16) that holds the compressor wheel (15) to the wheel assembly (19).6. Remove compressor wheel (15) and housing assembly (6) from wheel assembly (19). Remove piston ring (13) from the wheel assembly.7. Use tool (C), and remove snap ring (5) from housing assembly (6). Remove insert (14) and sleeve (18) from the housing assembly. Remove seal (22) from insert (14). Remove ring (20) from sleeve (18).8. Remove oil deflector (23), thrust ring (21), bearing assembly (7), spacer sleeve (24) and thrust ring (8) from housing assembly (6).9. Use tool (D), and remove snap ring (9) from the housing assembly. Remove bearing (25), and remove snap ring (10) with tool (D).10. Use tool (D), and remove snap ring (12) from the housing assembly. Remove bearing (26), and remove snap ring (11) with tool (D).11. Check all the parts of the turbocharger for damage. If any parts are damaged, use new parts for replacement. See Special Instruction Form No. SMHS6854 for turbocharger reconditioning. Also, see Guidelines For Reusable Parts, Form No. SEBF8018. The following steps are for assembly of the turbocharger.12. Make sure that all the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, put clean engine oil into the oil inlet of the turbocharger.
Make sure the snap rings that hold bearings (25) and (26) in housing assembly (6) are installed with the round edge of the outside diameter toward the bearing.
13. Install snap ring (11) with tool (D). Install bearing (26). Install snap ring (12) with tool (D).14. Install snap ring (10) with tool (D). Install bearing (25). Install snap ring (9) with tool (D).15. Put wheel assembly (19) in position on tool (B) with the threaded portion end up. Put 6V2055 High Vacuum Grease in the groove for piston ring (13) at assembly to one half or more of the depth of the groove all the way around.16. Install piston ring (13) in the groove in wheel assembly (19).17. Put housing assembly (6) in position on wheel assembly (19).18. Install thrust ring (8) and spacer sleeve (24) on wheel assembly (19).19. Make sure the screen is in place in bearing assembly (7). Install bearing assembly (7) over spacer sleeve (24). Make sure the screen in the bearing assembly is facing toward housing assembly (6) when it is installed.20. Install thrust ring (21) and oil deflector (23) on the wheel assembly. Put 6V2055 High Vacuum Grease in the groove of sleeve (18) to one half or more of the depth of the grooves all the way around.21. Install seal (22) on insert (14). Install ring (20) in the groove in sleeve (18). Put sleeve (18) in position in insert (14). Install the insert and sleeve as an assembly on the wheel assembly.22. Use tool (C), and install snap ring (5) to hold insert (14) in place.23. Install compressor wheel (15) at room temperature as follows:a. Put compressor wheel (15) in position on wheel assembly (19).b. Put a small amount of clean engine oil on the wheel assembly.
Do not put a side force on the shaft when the nut that holds the compressor wheel in position is tightened.
c. Install nut (16) on the wheel assembly. Tighten the nut to a torque of 14 to 17


Parts relay Volvo Penta:

876037
Relay kit
876037 Relay kit
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C,
1504951
Relay
1504951 Relay
2001; 2001B; 2001AG, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD21B; AQD21B, MD70B; MD70BK
873962
 
873962 Relay
2001; 2001B; 2001AG, D13B-F MG; D13B-E MG; D13B-E MG (FE), DH10A; DH10A 285; DH10A 360, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAD1240GE; TAD1241GE; TAD1242
1324492
Relay
1324492 Relay
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD32P; TAMD42WJ-A; KAD43P-A,
873611
 
873611 Relay
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD63L-A; TAMD63P-A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAM
873765
 
873765 Relay
4.3GXiE-225-R, 4.3GXiE-M, 4.3GXiE-P; 4.3GXiE-Q, 5.0GXiCE-270-R; 5.0GiCE-225-S, 5.0GXiCE-J; 5.0GXiCE-JF; 5.0GXiCE-M, 5.0GXiCE-P, 5.0GXiE-270-R, 5.0GXiE-JF; 5.0GXiE-J; 5.0OSiE-JF, 5.0GXiE-P, 5.7GiCE-300-J; 5.7GiCE-300-JF; 5.7GXiCE-J, 5.7GiCE-300-P; 5.7
3171420
Relay
3171420 Relay
1372, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A
8153600
Relay
8153600 Relay
TAMD61A; TAMD62A, TAMD71A; TAMD72A, TMD121C; TAMD121C; TAMD121D
Back to top